Paul, this did not work for

rickjbeats · ‎11-10-2014

I've got DHCP turned on using a 4506e (version 15) for my APs. When doing a show ip dhcp bind, the mac addresses for the APs show a lease, but does not show the address in CDP neighbor, making them unreachable. Can someone provide answers?

Bind

10.78.243.2 01e0.5fb9.43bb.b3 Nov 10 2014 01:25 PM Automatic
10.78.243.3 0150.3de5.8637.51 Nov 10 2014 01:25 PM Automatic
10.78.243.4 01c8.9c1d.f459.15 Nov 10 2014 01:25 PM Automatic
10.78.243.5 0150.3de5.8638.d1 Nov 10 2014 01:25 PM Automatic
10.78.243.6 01e0.5fb9.43bb.0c Nov 10 2014 01:25 PM Automatic
10.78.243.7 01e0.5fb9.43a2.10 Nov 10 2014 01:25 PM Automatic
10.78.243.8 0150.3de5.9326.7c Nov 10 2014 01:25 PM Automatic
10.78.243.9 01e0.5fb9.43bb.67 Nov 10 2014 01:25 PM Automatic
10.78.243.10 0150.3de5.8638.cf Nov 10 2014 01:25 PM Automatic
10.78.243.11 01e0.5fb9.43a7.ea Nov 10 2014 01:25 PM Automatic
10.78.243.12 01e0.5fb9.43a7.f9 Nov 10 2014 01:25 PM Automatic
10.78.243.13 0150.3de5.2f82.d2 Nov 10 2014 01:25 PM Automatic
10.78.243.14 0140.5539.ca94.d5 Nov 10 2014 01:25 PM Automatic
10.78.243.15 0150.3de5.8637.15 Nov 10 2014 01:25 PM Automatic
10.78.243.16 0130.e4db.8272.5c Nov 10 2014 01:25 PM Automatic
10.78.243.17 0140.5539.ca37.05 Nov 10 2014 01:25 PM Automatic
10.78.243.18 01e0.5fb9.43bb.7b Nov 10 2014 01:25 PM Automatic

CDP Neighbor

Device ID: name-ap18
Entry address(es):
Platform: cisco AIR-CAP3502I-A-K9, Capabilities: Router Trans-Bridge
Interface: GigabitEthernet4/1, Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 164 sec

Version :
Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 15.2(4)JB3, RELEASE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 18-Dec-13 21:36 by prod_rel_team

advertisement version: 2
Duplex: full
Power drawn: 15.400 Watts
Power request id: 28353, Power management id: 2
Power request levels are:15400 14500 0 0 0
Management address(es):

paul driver · ‎11-10-2014

Hello

cluster enable STAN

sh cluster candidates
                                                             |---Upstream---|
MAC Address    Name         Device Type      PortIf FEC Hops SN PortIf FEC
xxxx.xxxxx.xxx       ???????   Fax/x        1   1 Fax/x

SW#(config) cluster member 10 mac-address xxxx.xxxx.xxxx password stan ( enable password of remote switch)

sh cluster members

SN MAC Address    Name         PortIf FEC Hops   SN PortIf FEC State
10 xxxx.xxxx.xxxx Fax/x       1     1 Fax/x       Up

SW# rcommand 10

Then check the config of the aps

res

Paul

Please rate and mark as an accepted solution if you have found any of the information provided useful.
This then could assist others on these forums to find a valuable answer and broadens the community’s global network.

Kind Regards
Paul

rickjbeats · ‎11-10-2014

Paul, this did not work for us.

Leo Laohoo · ‎11-10-2014

When doing a show ip dhcp bind, the mac addresses for the APs show a lease, but does not show the address in CDP neighbor,

Maybe CDP is disabled on the interface/globally?

Cisco 3502i showing in DHCP Bind but not in cdp neighbor