Hello,
We currently are attempting to replace an older 5509 with a 6500 series switch (all version information will be below) but I am coming across a problem that I'd appreciate the community's help on please.
I'll start with posting the configuration of the new switch then describe the problem.
--------
Current configuration : 9033 bytes
!
upgrade fpd auto
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
service counters max age 5
!
hostname Router
!
!
no aaa new-model
ip subnet-zero
!
!
!
mls ip slb purge global
no mls acl tcam share-global
!
!
!
!
!
!
redundancy
mode sso
main-cpu
auto-sync running-config
!
spanning-tree mode pvst
no spanning-tree vlan 1,22
no diagnostic cns publish
no diagnostic cns subscribe
fabric timer 15
!
vlan internal allocation policy ascending
!
!
interface GigabitEthernet1/1
description VLAN22 Dungeon Connection
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 22
switchport mode trunk
no ip address
!
interface GigabitEthernet1/2
no ip address
shutdown
!
interface FastEthernet2/1
switchport
switchport access vlan 22
no ip address
<<other fast ethernet ports omitted>>
!
interface Vlan1
no ip address
!
interface Vlan22
description Dungeon Switch
ip address 192.168.22.4 255.255.255.0
ip helper-address 192.168.20.24
ip directed-broadcast 101
!
router rip
version 2
network 192.168.20.0
network 192.168.22.0
!
ip default-gateway 192.168.22.1
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.22.1
!
no ip http server
!
access-list 101 permit udp host 192.168.20.93 any eq snmp
!
!
!
dial-peer cor custom
!
!
!
!
line con 0
line vty 0 4
login
!
no cns aaa enable
end
------
The problem is this: after I setup the switch the VLAN I want to establish (VLAN 22) shows to be down/down when I do a show interface command.
The G1/1 interface (the gig interface on the Supervisor) shows to be up/up as does the FastEthernet port 2/1 when I plug in my laptop. However, since the VLAN is down I can't communicate back to the core switch which is on the other end of the connection (a 6506E)
The new switch has the following version settings:
Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF16, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by cisco Systems, Inc.
Compiled Tue 03-Mar-09 14:24 by kellythw
Image text-base: 0x40101040, data-base: 0x4295C840
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
BOOTLDR: s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF16, RELEASE SOFTWARE (fc2)
Router uptime is 17 hours, 49 minutes
Time since Router switched to active is 17 hours, 48 minutes
System returned to ROM by power cycle (SP by power-on)
System image file is "disk0:s222-ipservices_wan-mz.122-18.SXF16.bin"
cisco WS-C6506 (R7000) processor (revision 3.0) with 458752K/65536K bytes of memory.
Processor board ID SAL08239FVP
R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
SuperLAT software (copyright 1990 by Meridian Technology Corp).
X.25 software, Version 3.0.0.
Bridging software.
TN3270 Emulation software.
2 Virtual Ethernet/IEEE 802.3 interfaces
144 FastEthernet/IEEE 802.3 interfaces
2 Gigabit Ethernet/IEEE 802.3 interfaces
381K bytes of non-volatile configuration memory.
32768K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
