cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
107
Views
0
Helpful
3
Replies

CISCO 6500 VSS - Problem after convertion

Hello everyone! 

i need your help, i convert my cisco 6509E to VSS mode and after reboot, the SW2 present this problem 

 

******************

CEN_VSS#show mod sw 2
Switch Number: 2 Role: Virtual Switch Standby
---------------------- -----------------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1440V9W8
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1440VLL9
3 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1440VELK
4 6 Firewall Module WS-SVC-FWM-1 SAL1439UWS2
5 5 Supervisor Engine 720 10GE (Hot) VS-S720-10G SAL1440VME5

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 1cdf.0f90.3038 to 1cdf.0f90.3067 3.4 Unknown Unknown Other
2 c84c.757c.f57c to c84c.757c.f5ab 3.4 Unknown Unknown PwrDown
3 1cdf.0f7b.bd88 to 1cdf.0f7b.bd9f 5.0 Unknown Unknown PwrDown
4 f866.f29a.2230 to f866.f29a.2237 4.5 Unknown Unknown PwrDown
5 0024.14e5.5040 to 0024.14e5.5047 3.2 8.5(4) 12.2(33)SXI4 Ok

Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC SAL1440V9JN 4.1 Other
2 Centralized Forwarding Card WS-F6700-CFC SAL1440V165 4.1 PwrDown
3 Centralized Forwarding Card WS-F6700-CFC SAL1440VJC9 4.1 PwrDown
5 Policy Feature Card 3 VS-F6K-PFC3C SAL1440VF1T 1.1 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1439UQMF 5.1 Ok

Mod Online Diag Status
---- -------------------
1 Not Applicable
2 Not Applicable
3 Not Applicable
4 Not Applicable
5 Pass

 

*****

try to reset single module and i try to removed and inserted module SLOT 1,2,3 but nothing's changed, and i try to reboot the sw2.

this is example to my log:

 

Sep 10 13:39:06.617: %C6KPWR-SW2_SPSTBY-4-DISABLED: power to module in slot 3 set off (Module Failed SCP dnld)

Sep 10 13:43:28.841: SW1_SP: Switch 2 Physical Slot 3 - Module Type LINE_CARD removed

Sep 10 13:43:28.857: SW1_SP: Switch 2 Physical Slot 3 - Module Type LINE_CARD inserted

 

 

 

Everyone's tags (1)
3 REPLIES 3
VIP Advisor

Re: CISCO 6500 VSS - Problem after convertion

here is the troubleshoot guide :

 

https://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/116115-trouble-linecard-00.html

 

For now looks like Hardware issue, can you post complete Logs of boot

BB
*** Rate All Helpful Responses ***
Cisco Employee

Re: CISCO 6500 VSS - Problem after convertion

Cristina,

Before rebooting during the VSS conversion, how long had it been since the chassis was rebooted ?

You may be hitting this: https://www.cisco.com/c/en/us/support/docs/field-notices/637/fn63743.html 

Please call TAC and let them investigate.

Cheers,
Scott Hodgdon

Senior Technical Marketing Engineer

Enterprise Networking Group

Highlighted
Hall of Fame Community Legend

Re: CISCO 6500 VSS - Problem after convertion

Based on the serial numbers of the 6748-GE-TX and 6724-SFP, I would say all three were manufactured on the first week of October 2010.  

Because of this, I believe the following line cards are affected by the Memory Component Issue (Field Notice: FN - 63743 - Catalyst 6500 - Might Fail to Boot Up After a Software Upgrade or Power Cycle).

CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards