cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
503
Views
0
Helpful
3
Replies

Cisco Aironet AIR-LAP1142N-E-K9

I am using Cisco Aironet AIR-LAP1142N-E-K9 on my network and it's connected to Gigabitethernet port on my 3750 switch, but for some eason it's neotiating only 100Mbps all time even when I run speed auto from both sides. If I run 1000Mbps from the switch and the AP, I loose connectivity. Please find below details:


-------------------------
Device ID: BTaS-RYD-5F-AP02
Entry address(es): 
  IP address: 192.168.15.252
Platform: cisco AIR-LAP1142N-E-K9   ,  Capabilities: Trans-Bridge IGMP 
Interface: GigabitEthernet1/0/14,  Port ID (outgoing port): GigabitEthernet0
Holdtime : 138 sec

Version :
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)

 

Output from the switch interface:


Port          Name                        Status          Vlan       Duplex     Speed    Type
Gi1/0/14  ***BTAS-7flr-AP03*   connected    trunk        full          a-100     10/100/1000BaseTX

 

Yasir

 

3 Replies 3

Leo Laohoo
Hall of Fame
Hall of Fame

Run a TDR on your switch.   I am suspecting you've got a faulty cable.  

 

Do the following commands: 

 

1.  Command:  test cable tdr interface Gi1/0/14; 

2.  Wait for approximately 5 to 7 seconds to run the test; 

3.  Command:  sh cable tdr interface Gi1/0/14; and 

4.  Post the output to #3.

Please find below:

 

BTaS-7F-SW-2#test cable-diagnostics tdr interface gi

 

BTaS-7F-SW-2#test cable-diagnostics tdr interface gigabitEthernet 1/0/14

 

Link state may be affected during TDR test

 

TDR test started on interface Gi1/0/14

 

A TDR test can take a few seconds to run on an interface

 

Use 'show cable-diagnostics tdr' to read the TDR results.

 

BTaS-7F-SW-2#

 

BTaS-7F-SW-2#

 

BTaS-7F-SW-2#

 

BTaS-7F-SW-2#show cable-diagnostics tdr ?

 

  interface  Specify an interface for result

 

 

 

BTaS-7F-SW-2#show cable-diagnostics tdr int gi

 

BTaS-7F-SW-2#show cable-diagnostics tdr int gigabitEthernet 1/0/14

 

TDR test last run on: March 10 04:38:17

 

 

 

Interface Speed Local pair Pair length        Remote pair Pair status

 

--------- ----- ---------- ------------------ ----------- --------------------

 

Gi1/0/14  100M  Pair A     N/A                N/A         Not Completed

 

                Pair B     N/A                N/A         Not Completed

 

                Pair C     N/A                N/A         Not Completed

 

                Pair D     N/A                N/A         Not Completed

 

BTaS-7F-SW-2#

 

 

 

Link state may be affected during TDR test

Uhhhhh ... what ancient IOS are you running????

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: