cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
43208
Views
30
Helpful
30
Replies

Cisco Catalyst 9000 range VSS Support

AdamDownie12
Level 1
Level 1

Hello,

 

Does anyone know if the Cisco Catalyst 9000 range range supports VSS and if all the range supports VSS.

Read through all the data sheets and it is not listed anywhere.

Thank you.

30 Replies 30

Could you please provide us offical document for that

here is the link

 

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9400/software/release/16-6/release_notes/ol-16-6-9400.html

 

also, you can access the following link and check all supported features per platform or IOS Version

 

http://cfn.cloudapps.cisco.com/ITDIT/CFN/

 

 

Was told this last week regarding Stackwise Virtual Links on Cat 9500 and 9400

 

9500 SVL support is expected in 16.8.1 which should be on CCO towards end of this month. It will support StackWise Virtual (SVL) on 10G and 40G links for all 9500. However, SVL connections will not initially be supported on the uplink module. This should get enabled in a later release.

 

9400 chassis Stackwise-virtual (which offers the functionalities as VSS) is currently targeted with 16.9 release with single supervisor.  Support with dual-supervisor is under consideration.

9500 is already supporting SVL, but 9400 what I have received it will start supporting on the upcoming release version which supposed within this week or next week.

 

if any of Cisco development team can confirm to us, it would be great.

Okay great..

 

There’s an update from cisco, now SVL (a.k.a VSS) support on cat9400 series.

 

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9400/software/release/16-9/configuration_guide/ha/b_169_ha_9400_cg/configuring_cisco_stackwise_virtual.html

 

the thinks that make me confused last time was they said minimum supervisor C9400-SUP-1XL required, and now they said both Supervisor 1 Module (C9400-SUP-1) and Cisco Catalyst 9400 Series Supervisor 1XL Module (C9400-SUP-1XL) support SVL..

 

StackWise Virtual Link (SVL) connection “only through 10G or 40G uplink ports on the supervisor module (You cannot establish an SVL using a 10G port on one switch and a 40G port on the other switch.)”

and

Fast Hello Dual-active detection is supported only on supervisor module ports.

 

Hope this information helps.

cheers

.

I just got an update from Cisco,

 

Regarding the support of StackWise virtual on modular Catalyst 9400, it is going to be supported in the next release of IOS XE 16.9.1 targeted in July 2018. Please note, to support this, you would need to have new supervisors SUP-1XL as the previous generation of supervisor was targeted for the access layer, hence no HA like in collapsed core was not needed that time.

 

Is there a technical reason for not supporting SVLs with uplink modules at FCS?  Can Cisco share a roadmap of which version IOS-XE that uplink modules will be supported?  We purchased 9500-16X with 40G uplink modules and would like to use the 40G as the SVLs, but now are forced to drop down to last 10G ports.

Do C9410R support VSS ?

 

Datasheet says "Cisco StackWise Virtual is supported only on Cisco Catalyst 9404R and Cisco Catalyst 9407R switches"


@prashanma wrote:

Do C9410R support VSS ? 

According to the Release Notes for 16.9.1 (LINK), StackWise Virtual is supported only on 9404R & 9407R chassis: 

Cisco StackWise Virtual is a network system virtualization technology that pairs two switches into one virtual switch to simplify operational efficiency with a single control and management plane.

Note 

The feature is supported only on these chassis models and supervisor modules:

  • Chassis Models—Catalyst 9404R Switch and Catalyst 9407R Switch.

  • Supervisor Modules

    • Cisco Catalyst 9400 Series Supervisor 1 Module (C9400-SUP-1). The feature requires a special, additional, C9400-SUP-UPG-LIC= license with this supervisor module.

    • Cisco Catalyst 9400 Series Supervisor 1XL Module(C9400-SUP-1XL).

Hi, The document You provided says only 9500 are supported. Did not see any reference to 9400.

any update on VSS for 9400 ?


@mateens wrote:
any update on VSS for 9400 ?

Stackwise Virtual (aka VSS) support for 9400 requires 16.9.1 (read THIS).

As far as I know from Cisco, they haven't release any update till now.
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: