cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
40959
Views
55
Helpful
16
Replies
Highlighted
Beginner

Cisco model naming convention

Does anyone know where to find a posting of what the parts of a cisco model name mean?

ex. WS-C3560G-24TS

16 REPLIES 16
Highlighted
Advisor

Re: Cisco model naming convention

I've never seen an official doc on it, but as a partner, I occasionally see a quote that has something regarding it. For your example,

WS=Workgroup Switch

C=Cisco

3560=Hardware Platform

G=Gigabit

24=Number of ports (not always accurate because it doesn't always count uplink ports. It's usually the number of ports for access.)

T=Ethernet I think, however there is also P which is for PoE.

S=Standard Image

These can sometimes vary so don't take this as gospel, but it should be pretty close.

Hope it helps.

Highlighted
Beginner

Re: Cisco model naming convention

Thank you so much. it's very helpful

Highlighted
Hall of Fame Guru

Re: Cisco model naming convention

As noted, the naming convention isn't always conventional. ;)

I suggest getting a copy of the (free in soft copy, also orderable for a nominal cost or usually available through your Cisco account team if you have one) Cisco Product Quick Reference Guide and downloading it to your computer. It is published regularly and has a good overview of most of Cisco's products in one place.

See http://www.cisco.com/en/US/prod/qrg/index.html

Hope this helps.

Highlighted
Beginner

Re: Cisco model naming convention

You can deduce it easily enough:

WS = Switching

C = Catalyst

3560 = Model

G = Type

24 = Port no.

TS = Sub Type

Or just use the SVO/RMA tool on the website, it will show you a list of all the parts for product.

https://apps.cisco.com/qtc/config/html/configureHomeGuest.html

Highlighted
Beginner

Cisco model naming convention

Can any one provide me naming convention for below?

air-cap1602i-n-k9

C1921-3G-G-SEC/K9

Highlighted
Participant

Cisco model naming convention

AP:

  • AIR: Aironet
  • C: Controller-based
  • AP: Access point
  • 1602: model number
  • i: integrated antenna
  • K9: strong AES/3DES encryption
Highlighted
Beginner

Cisco model naming convention

Thanks you so much.

Apprecialte your help

Highlighted

Re: Cisco model naming convention

Hi Andras,

Can you please let me know where can I get most of Part numbers and model number catalog for routers and Voip phones. Would be a big help.

 

Thank You,

Gayan

Highlighted

Re: Cisco model naming convention

Hi,
Andras, much appreciated if you could let me know where can I find catalog for most of the Cisco routers, switches, APs and VOIP phones.
Highlighted
Beginner

I know this question was

I know this question was asked a while ago but here is what I found:

http://www.ciscopress.com/articles/printerfriendly/2106547

Highlighted
Beginner

There is no set location or

There is no set location or spread sheet you can refer to!

The recommendation is to read the document of the model you are interested in or do what "routeremperor" has suggested. Searching and developing the naming your self however; be careful; their are a lot of meaning to  one letter :-)

 

Raj

Highlighted
Beginner

Ex: WS-C2960X-48FPS-LWS =

Ex: WS-C2960X-48FPS-L

WS = Switch
C = Catalyst​

2960= Model
X = Series ( X *OR* XR )

48 = How many Ethernet 10/100/1000 ports (24 or 48 )

FP = Identify if there is POE or not, and also Identify the Watt of POE if exist. ( F = 740w *OR*  L= 320w , P= POE )  If no POE then we will use (T) Instead  

S = number of SFPs  ( it is used to identify number of SFPs , S= 4 SFP  *OR*  D= 2 SFP+ )

-L = IOS Feature set ( for X series :  -L = LAN BASE *OR* -LL = LAN lite ) , ( For XR : -IL = IP lite) 
 

NOTE: We have 2 Exceptions for this concept:

===================================

1- WS-C2960X-24PSQ-L : Watt not mentioned,S=4SFP , Q is a new symbol. 
This Switch have only 2 SFP and 2 1000BASE-T , Its is also have POE on just 8 ports with 92w.

2- WS-C2960X-48TS-LL : Although It supposed to have 4 SFP referring to the S symbol, But it has only 2 SFP.  ( When the IOS is -LL , Then there are only 2 SFP  even if we use the S symbol )
 

Highlighted
Beginner

Re: Ex: WS-C2960X-48FPS-LWS =

Hello , 

What that the diference between Part code with "= " at  the end and not ?

for example :  "GLC-SX-MMD=" and  "GLC-SX-MMD"

 

best Regard

Highlighted
Beginner

Re: Ex: WS-C2960X-48FPS-LWS =

GLC-SX-MMD - with chasis

GLC-SX-MMD= - without chasis

 

CreatePlease to create content
Content for Community-Ad