Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
Can someone help me figure this out? Unable to ssh from C9300 to a C1000 and it complains about hmac, kex and pretty much everything else. I am not clear on what I need to change, server/client on either to allow this to work? %SSH-3-NO_MATCH: No m...
Hi guys, I need a help with issue. Our customer is having 9200L as edge switches (varied models due to PoE demands), some stacked, mostly not. We are running Ansible automation and push commands every night around midnight. And there is one stack whi...
Resolved! no ip dhcp conflict logging
hi all,i have a little confuse about the command " no ip dhcp conflict logging ".i know this command is to disable logging the ip conflict. but as i know, DHCP will ping the IP which will assign to make sure the IP not be used.if the IP be used, will...
I have multiple setups with these network switches. At least on two different setups, we have connection issues with one of the ports (port #24). We verified that the port configuration has changed and the reminder of the ports configurations remain ...
HI Where can i find some step.fil for the CISCO PWR-IE240W-PCAC- CISCO IE3100 8P2CPOE Switch Bent Ole
Dear allWe are currently running 7x C9300-48P all with IOS-XE 17.12.XX.We are experiencing a strange issue where on 5x of the devices we get high latency when pinging the virtual switch interface that is used for CLI access. But it is only happening ...
3512XL, Tera Term serial consoleI think BAUD is set correctly because the switch responses to commands like enable but the characters are unrecognizable...What can be the cause of this problem?I tried recovery mode with 9600 BAUD and the image is wha...
I need to make sure that our Nexus switches are hardened on the Internet and I'm really bothered that the ACL for SNMP works but leaves the port open. The ACL works in that if I attempt this from a host not allowed in the ACL, the Nexus will not acce...
Hello everyone.What's your experience with xFSU upgrades? I know this feature is there for a while, but I don't know anyone that actually used in production.We are planning to upgrade a stack of C9300-48UXM, from 17.12.03 to 17.12.06.We can do it in ...
Hello community,I was practicing SPAN, RSPAN, and ERSPAN in my CML environment, and realized that the IOSvL2 switches don't seem to support ERSPAN (Of course they do RSPAN and SPAN at least). Is there a trick that I'm missing, or another image availa...
I think flash is corrupt, Anyone please help me to install IOSThanks,I have tried below but wont workswitch: dir usbflash0:Size Attributes Name- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -32768 drw- System Volume Information892195673 -r...
Resolved! C1200 802.1x Missing Settings
I have a C1200-24P-4G switch. For some reason even though i have enabled advanced view on the GUI, I cannot see all the 802.1x settings that the admin guide refers to. For example, the options for MAB is missing. When i go to port authentication and ...
Just a simple question why it's recommended to use both Portfast and BPDU Guard together apart from the very fact that both should be used in access switches ports connecting to end users?? Like BPDU Guard will still work if I don't have portfast con...
Hi, I have been trying to get a virtual IP address (Vlan 13 Gateway) to route out the internet.Everything is working fine from Sw1 and 2 as far as connectivity to the internet is concerned.SW3 gets DHCP addresses assigned fine and can ping everythin...
Are there any configuration guides available for this feature for Catalyst 9300/9300x? We would like to configure and test for an upcoming design.
