cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
11153
Views
0
Helpful
17
Replies

Connection to the device could not be established. Either the device is not reachable or the HTTP/HTTPS service is not enabled on the device.

jason
Level 1
Level 1

This Cisco 800 series has been "handed" to me to get configured...

I am having issues ussing CCP to connect to the device, I am getting"Connection to the device could not be established. Either the device is not reachable or the HTTP/HTTPS service is not enabled on the device."

I know I saved some wrong configuration but having a tough time figuring out where.  Can someone point out to a cisco newb where I am going wrong?

I have checked off the following troubleshooting and can't find where I made my mistake.

Connection to the device could not be 
established. Either the device is not reachable 
or the HTTP service is not enabled on the 
device.

This error message is displayed in one of the following conditions:

The internet connection is down.

The IP address of the device is wrong or the device is not reachable.

The CLI "ip route <x.x.x.x> <x.x.x.x> <x.x.x.x>" is missing in the configuration.

The wrong HTTP port is provided to Cisco CP to connect to the device.

The CLI "ip http server" is missing in the configuration for non-secure connection.

The CLI "ip http secure-server" is missing in the configuration for secure connection.

To configure the device as an HTTP or HTTPS server, enter the following commands:

Router> config terminal
Router(config)# ip http server
Router(config)# ip http secure-server

Any help with the proper commands would be greatly appreciated!

881W#show config

Using 5319 out of 262136 bytes

!

! No configuration change since last restart

! NVRAM config last updated at 14:54:38 PCTime Sat Dec 17 2011

!

version 15.1

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname 881W

!

boot-start-marker

boot system flash c880data-universalk9-mz.151-3.T2.bin

boot-end-marker

!

!

logging buffered 51200 warnings

enable secret 5 $1$0IZb$gTe9qzmC2khcz4q7t1H1r0

!

no aaa new-model

memory-size iomem 10

--More--                           clock timezone PCTime -5 0

clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00

crypto pki token default removal timeout 0

!

crypto pki trustpoint TP-self-signed-542214224

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-542214224

revocation-check none

!

!

crypto pki certificate chain TP-self-signed-542214224

certificate self-signed 01 nvram:IOS-Self-Sig#1.cer

ip source-route

!

!

!

ip dhcp excluded-address 10.10.10.1

!

ip dhcp pool ccp-pool

   import all

   network 10.10.10.0 255.255.255.248

   default-router 10.10.10.1

   lease 0 2

--More--                           !

!

ip cef

no ip domain lookup

ip domain name Masternet

no ipv6 cef

!

!

license udi pid CISCO881W-GN-A-K9 sn FTX152401DC

!

!

username ***** privilege 15 secret 5 $1$FJ5H$buqflzYdL8pf9wOuZE8wm/

!

!

!

!

!

class-map type inspect match-any ccp-cls-insp-traffic

match protocol dns

match protocol ftp

match protocol h323

match protocol https

match protocol icmp

--More--                            match protocol imap

match protocol pop3

match protocol netshow

match protocol shell

match protocol realmedia

match protocol rtsp

match protocol smtp

match protocol sql-net

match protocol streamworks

match protocol tftp

match protocol vdolive

match protocol tcp

match protocol udp

class-map type inspect match-all ccp-insp-traffic

match class-map ccp-cls-insp-traffic

class-map type inspect match-any ccp-cls-icmp-access

match protocol icmp

match protocol tcp

match protocol udp

class-map type inspect match-all ccp-invalid-src

match access-group 100

class-map type inspect match-all ccp-icmp-access

match class-map ccp-cls-icmp-access

--More--                           class-map type inspect match-all ccp-protocol-http

match protocol http

!

!

policy-map type inspect ccp-permit-icmpreply

class type inspect ccp-icmp-access

  inspect

class class-default

  pass

policy-map type inspect ccp-inspect

class type inspect ccp-invalid-src

  drop log

class type inspect ccp-protocol-http

  inspect

class type inspect ccp-insp-traffic

  inspect

class class-default

  drop

policy-map type inspect ccp-permit

class class-default

  drop

!

zone security out-zone

--More--                           zone security in-zone

zone-pair security ccp-zp-self-out source self destination out-zone

service-policy type inspect ccp-permit-icmpreply

zone-pair security ccp-zp-in-out source in-zone destination out-zone

service-policy type inspect ccp-inspect

zone-pair security ccp-zp-out-self source out-zone destination self

service-policy type inspect ccp-permit

!

!

!

!

!

!

!

interface FastEthernet0

!

interface FastEthernet1

!

interface FastEthernet2

!

interface FastEthernet3

!

interface FastEthernet4

--More--                            description $ES_WAN$

no ip address

duplex auto

speed auto

pppoe-client dial-pool-number 1

!

interface wlan-ap0

description Service module interface to manage the embedded AP

ip unnumbered Vlan1

arp timeout 0

!

interface Wlan-GigabitEthernet0

description Internal switch interface connecting to the embedded AP

!

interface Vlan1

description Bellsouth WAN$FW_INSIDE$$ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$

ip address 10.10.10.1 255.255.255.248

ip nat outside

ip virtual-reassembly in

zone-member security out-zone

ip tcp adjust-mss 1412

!

interface Dialer0

--More--                            description $FW_OUTSIDE$

ip address negotiated

ip mtu 1452

zone-member security out-zone

encapsulation ppp

dialer pool 1

dialer-group 1

ppp authentication chap pap callin

ppp chap hostname *******

ppp chap password 0 ********

ppp pap sent-username ******** password 0 ********

no cdp enable

!

ip forward-protocol nd

ip http server

ip http access-class 23

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip flow-top-talkers

top 10

--by bytes

cache-timeout 3000000

--More--                           !

ip route 0.0.0.0 0.0.0.0 FastEthernet4

!

logging esm config

access-list 23 permit 10.10.10.0 0.0.0.7

access-list 91 permit any

access-list 100 remark CCP_ACL Category=128

access-list 100 permit ip host 255.255.255.255 any

access-list 100 permit ip 127.0.0.0 0.255.255.255 any

access-list 101 permit ip any any

access-list 110 permit icmp any any echo

access-list 110 permit icmp any any echo-reply

access-list 110 permit icmp any any source-quench

access-list 110 permit icmp any any packet-too-big

access-list 110 permit icmp any any time-exceeded

dialer-list 1 protocol ip permit

no cdp run

!

!

!

!

banner login ^CYou are using a network that logs all users activities.  If you are not authorized disconnect now.^C

--More--                           !

line con 0

login local

no modem enable

line aux 0

line 2

no activation-character

no exec

transport preferred none

transport input all

line vty 0 4

access-class 23 in

privilege level 15

login local

transport input telnet ssh

!

scheduler max-task-time 5000

ntp update-calendar

ntp server 24.56.178.140 source Wlan-GigabitEthernet0

ntp server 64.90.182.55 prefer source Wlan-GigabitEthernet0

end

2 Accepted Solutions

Accepted Solutions

Hi,

take a look at my previous post , this is a ZBF config problem.

Regards.

Alain

Don't forget to rate helpful posts.

View solution in original post

Hi,

zone security in-zone

int vlan 1

no ip nat ouside

ip nat inside

no zone-member security out-zone

zone-member security in-zone

Regards.

Alain

Don't forget to rate helpful posts.

View solution in original post

17 Replies 17

Richard Burts
Hall of Fame
Hall of Fame

Jason

Can you tell us what is the source address when you attempt to use CCP? I am guessing that this is the problem. Look at these parts of the config

ip http access-class 23

access-list 23 permit 10.10.10.0 0.0.0.7

This says that the router will only accept connections from source addresses 10.10.10.1 through 10.10.10.6.

HTH

Rick

HTH

Rick

Do you think it is the preffered adapter messing things up?

C:\ipconfig /all

Windows IP Configuration

   Host Name . . . . . . . . . . . . : PC

   Primary Dns Suffix  . . . . . . . :
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection 2:

   Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : Marvell Yukon 88E8056 PCI-E Gigabit Ether
net Controller #2
   Physical Address. . . . . . . . . : 00-23-54-51-41-F7
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 10.10.10.2(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.248
   Default Gateway . . . . . . . . . : 10.10.10.1
   NetBIOS over Tcpip. . . . . . . . : Enabled

Ethernet adapter Masternet:

   Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : Marvell Yukon 88E8056 PCI-E Gigabit Ether
net Controller
   Physical Address. . . . . . . . . : 00-23-54-51-41-F8
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.1.113(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Saturday, December 17, 2011 3:54:53 PM
   Lease Expires . . . . . . . . . . : Sunday, December 18, 2011 3:54:53 PM
   Default Gateway . . . . . . . . . : 192.168.1.254
   DHCP Server . . . . . . . . . . . : 192.168.1.254
   DNS Servers . . . . . . . . . . . : 205.152.144.23
                                       205.152.132.23
                                       192.168.1.254
   NetBIOS over Tcpip. . . . . . . . : Enabled

Tunnel adapter isatap.{319730B2-D3E1-4D78-BC1E-A9F7827A84E8}:

   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes

Tunnel adapter Teredo Tunneling Pseudo-Interface:

   Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1851:27dc:3f57:fe8e(Pref
erred)
   Link-local IPv6 Address . . . . . : fe80::1851:27dc:3f57:fe8e%13(Preferred)
   Default Gateway . . . . . . . . . : ::
   NetBIOS over Tcpip. . . . . . . . : Disabled

Tunnel adapter isatap.{B794DE4E-C0A2-4CC6-A5D3-A5657D38F1B4}:

   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix  . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes

Jason

The PC seems to have 2 IP addresses and I do not see anything in what you posted that tells us which address is being used (and both addresses have the notation that they are preferred). So I am going to assume that it is likely that the device is using the 192.168.1.113 address and that this is causing the problem. I can suggest a couple of things that you could do that would prove this.

- you could add a line to access list 23 that permits 192.168.1.113 (premit the specific host, or permit a range of hosts that include this, or permit the entire 192.168.1.0 network). If you add the line and then access works you have prooved what was the problem and have also achieved a workaround for the problem.

- you could add a line to access list 23 with deny any and specifying the log parameter like this

access-list 23 deny any log

This will generate a log message which should tell you what address is attempting access. This could tell you exactly what the problem is but you would then have to decide whether it is better to do something on the host to get it to use the 10.10.10.2 address or to do something on the router to get it to accept the address.

HTH

Rick

As an after-thought can you tell us whether that host has 2 Ethernet cards? Perhaps the solution is as simple as moving the Ethernet connection to the other card.

HTH

Rick

Rick,

I did disable the 192.168.1.113 DHCP address and that still proved to not work.  I should of been more clear back when I posted the IPCONFIG.  On your advice I have switched the network cords around, and disabled the 192.x.x.x network for safe keeping.  No luck...

Here is the new access-lists info:

881W(config)#end

881W#

Dec 18 23:13:04.751: %SYS-5-CONFIG_I: Configured from console by ****** on consolewrite

Building configuration...

[OK]

881W#show access-lists

Standard IP access list 23

    10 permit any

Standard IP access list 91

    10 permit any

Extended IP access list 100

    10 permit ip host 255.255.255.255 any

    20 permit ip 127.0.0.0 0.255.255.255 any

Extended IP access list 101

    10 permit ip any any

Extended IP access list 110

    10 permit icmp any any echo

    20 permit icmp any any echo-reply

    30 permit icmp any any source-quench

    40 permit icmp any any packet-too-big

    50 permit icmp any any time-exceeded

881W#

As you can see I did the ole permit any and still not working.  Also below is my current IPCONFIG.

Windows IP Configuration

Ethernet adapter Masternet:

   Connection-specific DNS Suffix  . :

   IPv4 Address. . . . . . . . . . . : 192.168.1.122

   Subnet Mask . . . . . . . . . . . : 255.255.255.0

   Default Gateway . . . . . . . . . : 192.168.1.254

Ethernet adapter Cisco:

   Connection-specific DNS Suffix  . :

   IPv4 Address. . . . . . . . . . . : 10.10.10.2

   Subnet Mask . . . . . . . . . . . : 255.255.255.248

   Default Gateway . . . . . . . . . : 10.10.10.1

Tunnel adapter isatap.{319730B2-D3E1-4D78-BC1E-A9F7827A84E8}:

   Media State . . . . . . . . . . . : Media disconnected

   Connection-specific DNS Suffix  . :

Tunnel adapter Teredo Tunneling Pseudo-Interface:

   Connection-specific DNS Suffix  . :

   IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:30:2954:3f57:fe85

   Link-local IPv6 Address . . . . . : fe80::30:2954:3f57:fe85%13

   Default Gateway . . . . . . . . . : ::

Tunnel adapter isatap.{B794DE4E-C0A2-4CC6-A5D3-A5657D38F1B4}:

   Media State . . . . . . . . . . . : Media disconnected

   Connection-specific DNS Suffix  . :

As far the log reporting, here is what I set:

881W#show access-lists

Standard IP access list 23

    10 deny   any log

Standard IP access list 91

    10 permit any

Extended IP access list 100

    10 permit ip host 255.255.255.255 any

    20 permit ip 127.0.0.0 0.255.255.255 any

Extended IP access list 101

    10 permit ip any any

Extended IP access list 110

    10 permit icmp any any echo

    20 permit icmp any any echo-reply

    30 permit icmp any any source-quench

    40 permit icmp any any packet-too-big

    50 permit icmp any any time-exceeded

881W#show log

I took the NIC adapter up and down to make sure I saw active logging, this is the result:

Dec 18 23:32:59.179: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down

Dec 18 23:33:06.447: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up

Dec 18 23:33:07.447: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

I didn't see any activity from the CCP.  Any more advice?

Jason

Hi Jason,

Could you post your show version output? Make sure you've temporarily disabled your PC FW/AV.

Sent from Cisco Technical Support iPhone App

John,

I removed MS Security Essentials, and checked the Windows Firewall and all firewalls(zones) are set to off.  The CCP was working until I made some changes a couple days back.  The system (PC) I am using has not changed in really any way.  I was assuming I made a bonehead change and committed it before checking.  Looking over the config it seemed fine except for the local PC having two NICS.  I was using one NIC for my local LAN, and the other to connect to the CCP on the Cisco 881.

881W#show version
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(3)T2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 10-Aug-11 11:29 by prod_rel_team

ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)

881W uptime is 3 minutes
System returned to ROM by power-on
System restarted at 23:30:09 PCTime Sun Dec 18 2011
System image file is "flash:c880data-universalk9-mz.151-3.T2.bin"
Last reload type: Normal Reload


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
--More--                          
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco 881 (MPC8300) processor (revision 1.0) with 236544K/25600K bytes of memory.
Processor board ID FTX152401DC

5 FastEthernet interfaces
1 Gigabit Ethernet interface
1 terminal line
1 Virtual Private Network (VPN) Module
1 cisco Embedded AP (s)
256K bytes of non-volatile configuration memory.
126000K bytes of ATA CompactFlash (Read/Write)


License Info:

License UDI:
--More--                          
-------------------------------------------------
Device#   PID   SN
-------------------------------------------------
*0     CISCO881W-GN-A-K9     FTX152401DC    

License Information for 'c880-data'
    License Level: advsecurity   Type: Permanent
    Next reboot license Level: advsecurity


Configuration register is 0x2102

hi jason,

can you do the below and try again?

no ip source-route

John,

No luck, still not working and giving the same error.

Latest config:

Using 5344 out of 262136 bytes
!
! Last configuration change at 10:33:56 PCTime Mon Dec 19 2011 by jmorano
! NVRAM config last updated at 10:33:58 PCTime Mon Dec 19 2011 by jmorano
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname 881W
!
boot-start-marker
boot system flash c880data-universalk9-mz.151-3.T2.bin
boot-end-marker
!
!
logging buffered 51200 warnings
enable secret 5 $1$0IZb$gTe9qzmC2khcz4q7t1H1r0
!
no aaa new-model
memory-size iomem 10
--More--                           clock timezone PCTime -5 0
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki token default removal timeout 0
!
crypto pki trustpoint TP-self-signed-542214224
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-542214224
revocation-check none
!
!
crypto pki certificate chain TP-self-signed-542214224
certificate self-signed 01 nvram:IOS-Self-Sig#1.cer
ip source-route
!
!
!
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool
   import all
   network 10.10.10.0 255.255.255.248
   default-router 10.10.10.1
   lease 0 2
--More--                           !
!
ip cef
no ip domain lookup
ip domain name Masternet
no ipv6 cef
!
!
license udi pid CISCO881W-GN-A-K9 sn FTX152401DC
!
!
username jmorano privilege 15 secret 5 $1$FJ5H$buqflzYdL8pf9wOuZE8wm/
!
!
!
!
!
class-map type inspect match-any ccp-cls-insp-traffic
match protocol dns
match protocol ftp
match protocol h323
match protocol https
match protocol icmp
--More--                            match protocol imap
match protocol pop3
match protocol netshow
match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
--More--                           class-map type inspect match-all ccp-protocol-http
match protocol http
!
!
policy-map type inspect ccp-permit-icmpreply
class type inspect ccp-icmp-access
  inspect
class class-default
  pass
policy-map type inspect ccp-inspect
class type inspect ccp-invalid-src
  drop log
class type inspect ccp-protocol-http
  inspect
class type inspect ccp-insp-traffic
  inspect
class class-default
  drop
policy-map type inspect ccp-permit
class class-default
  drop
!
zone security out-zone
--More--                           zone security in-zone
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
!
!
!
!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
--More--                            description $ES_WAN$
no ip address
duplex auto
speed auto
pppoe-client dial-pool-number 1
!
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
!
interface Vlan1
description Bellsouth WAN$FW_INSIDE$$ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.10.10.1 255.255.255.248
ip nat outside
ip virtual-reassembly in
zone-member security out-zone
ip tcp adjust-mss 1412
!
interface Dialer0
--More--                            description $FW_OUTSIDE$
ip address negotiated
ip mtu 1452
zone-member security out-zone
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname *********
ppp chap password 0 ********
ppp pap sent-username ******
no cdp enable
!
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip flow-top-talkers
top 10
sort-by bytes
cache-timeout 3000000
--More--                           !
ip route 0.0.0.0 0.0.0.0 FastEthernet4
!
logging esm config
access-list 23 permit any
access-list 91 permit any
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip host 255.255.255.255 any
access-list 100 perm  ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 110 permit icmp any any echo
access-list 110 permit icmp any any echo-reply
access-list 110 permit icmp any any source-quench
access-list 110 permit icmp any any packet-too-big
access-list 110 permit icmp any any time-exceeded
dialer-list 1 protocol ip permit
no cdp run

!
!
!
!
banner login ^CYou are using a network that logs all users activities.  If you are not authorized disconnect now.^C
--More--                           !
line con 0
login local
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
ntp update-calendar
ntp server 24.56.178.140 source Wlan-GigabitEthernet0
ntp server 64.90.182.55 prefer source Wlan-GigabitEthernet0
end

Jason

I am a bit confused about how it is configured. First you tell us this:

881W#show access-lists

Standard IP access list 23

    10 permit any

but then you also show us this

881W#show access-lists

Standard IP access list 23

    10 deny   any log

so I am really confused about the content of access list 23. Perhaps the best solution is to ask you to post a fresh copy of the output of show run.

HTH

Rick

HTH

Rick

881W#show run
Building configuration...

Current configuration : 6594 bytes
!
! No configuration change since last restart
! NVRAM config last updated at 23:30:52 PCTime Sun Dec 18 2011
!
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname 881W
!
boot-start-marker
boot system flash c880data-universalk9-mz.151-3.T2.bin
boot-end-marker
!
!
logging buffered 51200 warnings
enable secret 5 $1$0IZb$gTe9qzmC2khcz4q7t1H1r0
!
no aaa new-model
--More--                           memory-size iomem 10
clock timezone PCTime -5 0
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki token default removal timeout 0
!
crypto pki trustpoint TP-self-signed-542214224
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-542214224
revocation-check none
!
!
crypto pki certificate chain TP-self-signed-542214224
certificate self-signed 01
  30820229 30820192 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
  30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274
  69666963 6174652D 35343232 31343232 34301E17 0D313131 32313930 34333035
  315A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F
  532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3534 32323134
  32323430 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100
  A25FA6DA 732919AD 52606CBF E0CA905E 6F09C2FE 12A66B53 51D0967A CF4A6CD2
  768A8EF7 8170F01A 00673D2A B8A92FA2 15981052 5C8DE4DF E4AD08CD 89BB75E0
  BB8AFEB0 229DEC04 419019E6 CF51AEF1 54539B92 821FB287 8AE98C43 4337890E
  8F23318F EF02CAD4 7EDB15DC 841D7ACE 731BCB3D A65B1935 5F030EB8 720777E3
--More--                             02030100 01A35330 51300F06 03551D13 0101FF04 0530030F1 01FF301 0603551D
  23041830 16801450 28EB9B88 DC3E5C80 035D3EC8 DA79DEA8 83E11430 1D060355
  1D0E0416 04145028 EB9B88DC 3E5C8003 5D3EC8DA 79DEA883 E114300D 06092A86
  4886F70D 01010405 00038181 0085F224 F8273C2D E639AAA9 BD0D0AD8 775ADDB1
  C38BD8A0 F8EB8A02 AF4A75DE 6E561CAD 524FBA59 31C58805 6EB92D6B 479764E1
  3BFC656D BC0E7C8A C1CEBB28 9D95A202 339E8988 90CF67BC F7BAA4C8 FA31A725
  31439CF7 3C9A6824 BB79C505 FC06F068 B833B27A 4881E93D 20E71EA0 3B4F4E1D
  E9D13421 4C0FF6E6 2A9C063D 02
   quit
ip source-route
!
!
!
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool ccp-pool
   import all
   network 10.10.10.0 255.255.255.248
   default-router 10.10.10.1
   lease 0 2
!
!
ip cef
--More--                           no ip domain lookup
ip domain name Masternet
no ipv6 cef
!
!
license udi pid CISCO881W-GN-A-K9 sn FTX152401DC
!
!
username ******* privilege 15 secret 5 $1$FJ5H$buqflzYdL8pf9wOuZE8wm/
!
!
!
!
!
class-map type inspect match-any ccp-cls-insp-traffic
match protocol dns
match protocol ftp
match protocol h323
match protocol https
match protocol icmp
match protocol imap
match protocol pop3
match protocol netshow
--More--                            match protocol shell
match protocol realmedia
match protocol rtsp
match protocol smtp
match protocol sql-net
match protocol streamworks
match protocol tftp
match protocol vdolive
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-insp-traffic
match class-map ccp-cls-insp-traffic
class-map type inspect match-any ccp-cls-icmp-access
match protocol icmp
match protocol tcp
match protocol udp
class-map type inspect match-all ccp-invalid-src
match access-group 100
class-map type inspect match-all ccp-icmp-access
match class-map ccp-cls-icmp-access
class-map type inspect match-all ccp-protocol-http
match protocol http
!
--More--                           !
policy-map type inspect ccp-permit-icmpreply
class type inspect ccp-icmp-access
  inspect
class class-default
  pass
policy-map type inspect ccp-inspect
class type inspect ccp-invalid-src
  drop log
class type inspect ccp-protocol-http
  inspect
class type inspect ccp-insp-traffic
  inspect
class class-default
  drop
policy-map type inspect ccp-permit
class class-default
  drop
!
zone security out-zone
zone security in-zone
zone-pair security ccp-zp-self-out source self destination out-zone
service-policy type inspect ccp-permit-icmpreply
--More--                           zone-pair security ccp-zp-in-out source in-zone destination out-zone
service-policy type inspect ccp-inspect
zone-pair security ccp-zp-out-self source out-zone destination self
service-policy type inspect ccp-permit
!
!
!
!
!
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
description $ES_WAN$
no ip address
duplex auto
--More--                            speed auto
pppoe-client dial-pool-number 1
!
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
arp timeout 0
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
!
interface Vlan1
description Bellsouth WAN$FW_INSIDE$$ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.10.10.1 255.255.255.248
ip nat outside
ip virtual-reassembly in
zone-member security out-zone
ip tcp adjust-mss 1412
!
interface Dialer0
description $FW_OUTSIDE$
ip address negotiated
ip mtu 1452
--More--                            zone-member security out-zone
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname ***********
ppp chap password 0 **********
ppp pap sent-username ********** password 0 **********
no cdp enable
!
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip flow-top-talkers
top 10
sort-by bytes
cache-timeout 3000000
!
ip route 0.0.0.0 0.0.0.0 FastEthernet4
!
--More--                           logging esm config
access-list 23 permit any
access-list 91 permit any
access-list 100 remark CCP_ACL Category=128
access-list 100 permit ip host 255.255.255.255 any
access-list 100 permit ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 110 permit icmp any any echo
access-list 110 permit icmp any any echo-reply
access-list 110 permit icmp any any source-quench
access-list 110 permit icmp any any packet-too-big
access-list 110 permit icmp any any time-exceeded
dialer-list 1 protocol ip permit
no cdp run

!
!
!
!
banner login ^CYou are using a network that logs all users activities.  If you are not authorized disconnect now.^C
!
line con 0
--More--                            login local
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input telnet ssh
!
scheduler max-task-time 5000
ntp update-calendar
ntp server 24.56.178.140 source Wlan-GigabitEthernet0
ntp server 64.90.182.55 prefer source Wlan-GigabitEthernet0
end

Jason

Thanks for posting the output of show run. That clearly shows that the access class is no longer a potential problem. If CCP is still not working then we need to look for something else.

Can you post the output of tracert from your PC to the router?

If you attempt to use CCP do you get any kind of response?

HTH

Rick

HTH

Rick

Hi,

policy-map type inspect ccp-permit

class class-default

  drop

zone-pair security ccp-zp-out-self source out-zone destination self

service-policy type inspect ccp-permit

interface Vlan1

description Bellsouth WAN$FW_INSIDE$$ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$

ip address 10.10.10.1 255.255.255.248

ip nat outside

ip virtual-reassembly in

zone-member security out-zone

you are denying all communication from VLAN1 interface to the router and tht's why CCP is not working.

Just move interface VLAN 1 int zone-security in-zone and it will work

I also noticed you put your inside interface as a NAT outside interface but it should be a NAT inside interface and furthermore I do not see any other NAT configuration. you should configure Dialer interface as NAt outside and then create an ACL for natting in-zone to out-zone Dialer interface and a NAT statement for this like this:

access-list 199 permit ip 10.10.10.0 0.0.0.7 any

ip nat inside source list 199 interface Dialer0

You should also change your default static like this

no ip route 0.0.0.0 0.0.0.0 FastEthernet4

ip route 0.0.0. 0.0.0.0 Dialer0

Also add following global config command for testing your ZBF: ip inspect log drop-pkt

Regards.

Alain

Don't forget to rate helpful posts.

Alain,

you are denying all communication from VLAN1 interface to the router and tht's why CCP is not working.

Just move interface VLAN 1 int zone-security in-zone and it will work

I also noticed you put your inside interface as a NAT outside interface but it should be a NAT inside interface and furthermore I do not see any other NAT configuration.

Your explanation is now making more sense.  I figured I locked myselrf out by misconfiguring the NAT.  Can you assist in the proper way I can move the Vlan per your comments above?

I greatly appreciate the proper verbiage for the:

access-list 199 permit ip 10.10.10.0 0.0.0.7 any

ip nat inside source list 199 interface Dialer0

You should also change your default static like this

no ip route 0.0.0.0 0.0.0.0 FastEthernet4

ip route 0.0.0. 0.0.0.0 Dialer0

Also add following global config command for testing your ZBF: ip inspect log drop-pkt

Can you assist me in the Vlan move?  Thanks!

Jason

Hi,

zone security in-zone

int vlan 1

no ip nat ouside

ip nat inside

no zone-member security out-zone

zone-member security in-zone

Regards.

Alain

Don't forget to rate helpful posts.
Review Cisco Networking for a $25 gift card