cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
24593
Views
10
Helpful
5
Replies

Difference between GLC-LH-SM and SFP-GE-L

Hi,

Could someone explain me what is the difference between these two modules?.

Thanks,

Jaime.

2 Accepted Solutions

Accepted Solutions

acampbell
VIP Alumni
VIP Alumni

Jaime

The differnce is the typeof fibre connector

GBIC Module and SFP Module Cabling and Connection Equipment

The GBIC module port is a 1000-Mbps optical interface in the form of an SC-type duplex port (see Figure 1) that supports IEEE 802.3z interfaces compliant with the 1000BASE-X standard.

Table 6 provides cabling specifications for the GBIC modules and SFP modules that you install in Gigabit Ethernet devices. Note that all GBIC module ports have SC-type connectors and all SFP ports have LC-type connectors.

The minimum cable distance for the WS-G5484 or GLC-SX-MM and WS-G5486 or GLC-LH-SM (multimode fiber [MMF] and single-mode fiber [SMF]) is 6.5 feet (2 m), and the minimum link distance for the WS-G5487 or GLC-ZX-SM is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance for the WS-G5487 or GLC-ZX-SM is 24.9 miles (40 km).

http://www.cisco.com/en/US/docs/routers/7200/install_and_upgrade/gbic_sfp_modules_install/5067g.html#wp54251

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.

View solution in original post

Raju Sekharan
Cisco Employee
Cisco Employee

Hi Jaime

GLC-LH-SM doesn't support DOM

SFP-GE-L support DOM

Here is the link

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html

What is DOM?

digital optical monitoring (DOM). This feature gives the end user the  ability to monitor real-time parameters of the SFP, such as optical  output power, optical input power, temperature, laser bias current, and  transceiver supply voltage.

/Raju

** Please rate if the post helps***

View solution in original post

5 Replies 5

acampbell
VIP Alumni
VIP Alumni

Jaime

The differnce is the typeof fibre connector

GBIC Module and SFP Module Cabling and Connection Equipment

The GBIC module port is a 1000-Mbps optical interface in the form of an SC-type duplex port (see Figure 1) that supports IEEE 802.3z interfaces compliant with the 1000BASE-X standard.

Table 6 provides cabling specifications for the GBIC modules and SFP modules that you install in Gigabit Ethernet devices. Note that all GBIC module ports have SC-type connectors and all SFP ports have LC-type connectors.

The minimum cable distance for the WS-G5484 or GLC-SX-MM and WS-G5486 or GLC-LH-SM (multimode fiber [MMF] and single-mode fiber [SMF]) is 6.5 feet (2 m), and the minimum link distance for the WS-G5487 or GLC-ZX-SM is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance for the WS-G5487 or GLC-ZX-SM is 24.9 miles (40 km).

http://www.cisco.com/en/US/docs/routers/7200/install_and_upgrade/gbic_sfp_modules_install/5067g.html#wp54251

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.

Both the GLC-LH-SM and SFP-GE-L are available in the SFP form factor. This is information is not entirely helpful...

Raju Sekharan
Cisco Employee
Cisco Employee

Hi Jaime

GLC-LH-SM doesn't support DOM

SFP-GE-L support DOM

Here is the link

http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html

What is DOM?

digital optical monitoring (DOM). This feature gives the end user the  ability to monitor real-time parameters of the SFP, such as optical  output power, optical input power, temperature, laser bias current, and  transceiver supply voltage.

/Raju

** Please rate if the post helps***

Thanks for your help.

One more question, These modules are supported in any LC that support SFP ports?.

Review Cisco Networking products for a $25 gift card