cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
4804
Views
0
Helpful
7
Replies
Highlighted

Enable PoE in Cisco 2900 Series

hi team,

I have a problem, when connect a camara (PoE) in any port to the  router 2900

I dont see connected this appliance and I can´t power the camara.

these are outputs:

2900-GTD#sh version

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(3)T4, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Thu 24-May-12 02:32 by prod_rel_team

Technology Package License Information for Module:'c2900'

-----------------------------------------------------------------

Technology    Technology-package           Technology-package

              Current       Type           Next reboot

------------------------------------------------------------------

ipbase        ipbasek9      Permanent      ipbasek9

security      securityk9    Evaluation     securityk9

uc            uck9          Permanent      uck9

data          None          None           datak9

Configuration register is 0x2102

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

2900-GTD#sh p?

pagp        parameter-map  parser           pas

pci         per-call       performance      persistent

platform    pm             policy-firewall  policy-manager

policy-map  ppp            pppatm           pppoe

presence    printers       privilege        processes

protocols

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

in this moment the camara is connected and this is the ouput ..

.

2900-GTD#sh interfaces status

Port    Name               Status       Vlan       Duplex Speed Type

Gi0/0/0                    notconnect   300          auto    auto 10/100BaseTX

Gi0/0/1                    notconnect   300          auto    auto 10/100BaseTX

Gi0/0/2                    notconnect   300          auto    auto 10/100BaseTX

Gi0/0/3                    notconnect   300          auto    auto 10/100BaseTX

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

Perhaps this is a problem with IOS or license?

2900-GTD#show license

Index 1 Feature: ipbasek9

        Period left: Life time

        License Type: Permanent

        License State: Active, In Use

        License Count: Non-Counted

        License Priority: Medium

Index 2 Feature: securityk9

        Period left: 7  weeks 3  days

        Period Used: 1  week  0  day

        License Type: Evaluation

        License State: Active, In Use

        License Count: Non-Counted

        License Priority: Low

Index 3 Feature: uck9

        Period left: Life time

        License Type: Permanent

        License State: Active, In Use

        License Count: Non-Counted

        License Priority: Medium

Index 4 Feature: datak9

        Period left: 8  weeks 4  days

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Active, Not in Use, EULA accepted

        License Count: Non-Counted

        License Priority: Low

Index 5 Feature: gatekeeper

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 6 Feature: SSL_VPN

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: 0/0  (In-use/Violation)

        License Priority: None

Index 7 Feature: ios-ips-update

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 8 Feature: SNASw

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

Index 9 Feature: hseck9

Index 10 Feature: cme-srst

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: 0/0  (In-use/Violation)

        License Priority: None

Index 11 Feature: WAAS_Express

        Period left: Not Activated

        Period Used: 0  minute  0  second

        License Type: EvalRightToUse

        License State: Not in Use, EULA not accepted

        License Count: Non-Counted

        License Priority: None

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

if anybody have information about this problem, please let me know

Regards,

Yerko.

7 REPLIES 7
Highlighted
Enthusiast

Issue the command 'sh power inline' and post the output.

Martin

Highlighted

it's so strange because the command "power inline" is not present in the command list.

output:

2900-GTD#sh p?

pagp        parameter-map  parser           pas

pci         per-call       performance      persistent

platform    pm             policy-firewall  policy-manager

policy-map  ppp            pppatm           pppoe

presence    printers       privilege        processes

protocols

Highlighted

Post the output to the command "sh inventory".  This will determine if your router is spec-ed up for PoE or not.

Highlighted

2900-GTD#sh inventory

NAME: "CISCO2901/K9 chassis", DESCR: "CISCO2901/K9 chassis"

PID: CISCO2901/K9      , VID: V02 , SN: FTX15040378

NAME: "2 port SHDSL with annex A,B,F and G on Slot 0 SubSlot 1", DESCR: "2 port SHDSL with annex A,B,F and G"

PID: HWIC-2SHDSL       , VID: V01 , SN: FOC103802CN

NAME: "4 Port GE POE EHWIC Switch on Slot 0 SubSlot 3", DESCR: "4 Port GE POE EHWIC Switch"

PID: EHWIC-4ESG-P      , VID: V01 , SN: FOC15256PEV

NAME: "C2901 AC-POE Power Supply", DESCR: "C2901 AC-POE Power Supply"

PID: PWR-2901-POE      , VID:    , SN:

Highlighted

I have other appliance (Cisco 1941) with the same problem.

note: I cant see the SN in power supply (PID: PWR-1941-2901-AC  , VID:    , SN:  )    why?

RTR-GTD#sh inventory

NAME: "CISCO1941/K9", DESCR: "CISCO1941/K9 chassis, Hw Serial#: FTX140683HU, Hw Revision: 1.0"

PID: CISCO1941/K9      , VID: V01 , SN: FTX140683HU

NAME: "4 Port GE POE EHWIC Switch on Slot 0 SubSlot 0", DESCR: "4 Port GE POE EHWIC Switch"

PID: EHWIC-4ESG-P      , VID: V01 , SN: FOC15256PD8

NAME: "3G WWAN EHWIC-QuadBand HSPA+R7/HSPA/UMTS QuadBand EDGE/GPRS and GPS on Slot 0 SubSlot 1", DESCR: "3G WWAN EHWIC-QuadBand HSPA+R7/HSPA/UMTS QuadBand EDGE/GPRS and GPS"

PID: EHWIC-3G-HSPA+7   , VID: V01 , SN: FOC17095JVG

NAME: "Modem 0 on Cellular0/1/0", DESCR: "Sierra Wireless MC8705"

PID: MC8705            , VID: 1.0, SN: 357115040620002

NAME: "C1941/C2901 AC Power Supply", DESCR: "C1941/C2901 AC Power Supply"

PID: PWR-1941-2901-AC  , VID:    , SN:           

RTR-GTD#

Highlighted

NAME: "C2901 AC-POE Power Supply", DESCR: "C2901 AC-POE Power Supply"

PID: PWR-2901-POE      , VID:    , SN:

First router will support PoE modules.  Second one does not show to have a PoE power supply.

Highlighted

Hi,

I think you will need the ILPM-4 inline power module which is a daughter card for the EHWIC to use POE.

Following might be able to help:

http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/qa_c67-612908.html

Thanks

Ankur

"Please rate the post if found useful"


Content for Community-Ad