01-23-2022 08:09 AM
Hello All,
I have never worked with with extended vlans, but I have a customer who sent their vlan IDs they won't configured and they start at 2000. I have set the switch to VTP Transparent mode and created the vlans, but I need these to be routed. When I create an actual vlan interface, the status shows up, but the protocol shows down. Is it possible to create vlan interfaces for extended vlans?
Switchin
Thanks,
Bryan
Solved! Go to Solution.
01-24-2022 04:22 PM - edited 01-24-2022 04:23 PM
Try switchport autostate exclude under SVI interface - tells the switch to no longer consider the state of that port in its determination as to whether the SVI should be up or down.
cisco 9300 should support that command and exclude vlan 2000 SVI for so called auto vlan check (PT does not).
Regards, ML
**Please Rate All Helpful Responses **
01-23-2022 08:18 AM
Can give us more information what switch and what IOS Code, yes that is possible,
SVI Interface vlan 2000 only be up/up - when any access port to be part of the VLAN and device connected to that port to become up.
or this should be allowed in Port-channel ? (this is my assumption)
if you looking more advice, then please post the information below :
show VLAN
show ip interface brief
show interface vlan 2000
show span vlan 2000
01-23-2022 08:42 AM
Thanks for the response. I don't have access to the switch at present, but I have done some test scenarios on 3650 in packet tracer and it isn't working. The customer switch is cisco 9300. Here is the config I am using:
vtp mode transparent
!
spanning-tree mode pvst
!
vlan 10
name testvlan10
!
vlan 2000
name testvlan2000
!
interface GigabitEthernet1/0/1
switchport mode trunk
!
interface Vlan10
mac-address 0009.7caa.2501
ip address 10.10.10.1 255.255.255.0
!
interface Vlan2000
mac-address 0009.7caa.2502
ip address 10.124.25.1 255.255.255.0
Interface IP-Address OK? Method Status Protocol
GigabitEthernet1/0/1 unassigned YES unset up up
Vlan10 10.10.10.1 YES manual up up
Vlan2000 10.124.25.1 YES manual up down
I have a access switch connected to the core with the vlans and it is trunked. Vlan 10 comes up, but not vlan 2000
01-23-2022 11:58 AM - edited 01-23-2022 12:04 PM
At this information, we are not sure what is wrong. i am not a Packet tracer user, as i know PT does not support Extend vlan as per the document, this might have changed in due course of the latest version.
for extended we use spanning-tree config -spanning-tree extend system-id
when you get the chance i would like to see the below output as asked before, also other side switch config.
show VLAN show ip interface brief show interface vlan 2000 show span vlan 2000
show interface trunk
show vtp status
01-25-2022 12:04 AM
Hi,
Try to create vlan 2000 on the access switch as well.
You might need to change VTP to transparent as well.
Assign it to trunk port if it is not.
Regards,
Ventsi
01-23-2022 12:00 PM - edited 01-23-2022 12:05 PM
Hi,
try the show int trunk command and make sure vlan 2000 is there.
interface igabitEthernet1/0/1
switchport mode trunk
switchport trunk allowed vlan add 2000
Another thing you can try is to set another port as access (try to connect it to another device for testing)for vlan 2000 and see if it changes status up:
int gi1/0/x
switchport mode access
switchport access vlan 2000
01-24-2022 04:22 PM - edited 01-24-2022 04:23 PM
Try switchport autostate exclude under SVI interface - tells the switch to no longer consider the state of that port in its determination as to whether the SVI should be up or down.
cisco 9300 should support that command and exclude vlan 2000 SVI for so called auto vlan check (PT does not).
Regards, ML
**Please Rate All Helpful Responses **
01-25-2022 02:11 PM
Thanks ML,
That was the issue. PT doesn't support extended vlans.
Best,
Bryan
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: