Facing issue while setting up WS-SVC-WISM2-K9 on Cisco 6509 switch

manish_3191 · ‎08-15-2012

Hi Team,

I am trying to setup WS-SVC-WISM2-K9 on cisco 6509 switch with IOS version 12.2(33)SXJ1.

I have completed the below config and seeing service-port up but not coming in oper-up status.

I have installed WiSM module in slot 8 and seeing TG8/1, T8/2,G8/3 and G8/4 switch ports under module 8.

I am seeing only the automatically created port-channel 415 up with only T8/1 in it which strange to me.

I cant modify those interfaces as seeing error " These interfaces can not be modified.

Please provide suggestion about wht could be the wrong here?

COR-01#sh wism status

Service Vlan : 93, Service IP Subnet : 1.1.1.1/255.255.255.0

WLAN

Slot Controller Service IP Management IP SW Version Controller Type Status

----+-----------+----------------+----------------+------------+------------------+---------------

8 1 0.0.0.0 0.0.0.0 WS-SVC-WISM-2-K9 Service Port Up

JP2-RDC-COR-01#sh wism module 8 controller 1 status

WiSM Controller 1 in Slot 8 configured with auto-lag

Operational Status of the Controller : Service Port Up

Service VLAN : 93

Service Port : 3

Service Port Mac Address : 30e4.db38.9981

Service IP Address : 0.0.0.0

Management IP Address : 0.0.0.0

Software Version :

Port Channel Number : 415

Allowed-vlan list : 90,800,810

Native VLAN ID : 90

WCP Keep Alive Missed : 0

JP2-RDC-COR-01#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16084N3K

2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16085AEH

3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16159JHP

4 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16085099

5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1550Y2C7

8 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL16159DWW

9 16 CEF720 16 port 10GBaseT WS-X6716-10T SAL1626F9HR

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 c464.1305.b274 to c464.1305.b2a3 4.2 12.2(18r)S1 12.2(33)SXJ1 Ok

2 c464.1387.f5b4 to c464.1387.f5e3 4.2 12.2(18r)S1 12.2(33)SXJ1 Ok

3 5057.a866.6c98 to 5057.a866.6cc7 4.2 12.2(18r)S1 12.2(33)SXJ1 PwrDown

4 f0f7.556a.2bc0 to f0f7.556a.2bef 4.2 12.2(18r)S1 12.2(33)SXJ1 PwrDown

5 5475.d07b.62d0 to 5475.d07b.62d7 4.1 8.5(4) 12.2(33)SXJ1 Ok

8 0007.7d8c.5390 to 0007.7d8c.539f 1.1 12.2(18r)S1 12.2(33)SXJ1 Ok

9 442b.034f.7410 to 442b.034f.741f 2.1 12.2(18r)S1 12.2(33)SXJ1 Ok

TenGigabitEthernet8/1 unassigned YES unset up up

TenGigabitEthernet8/2 unassigned YES unset down down

GigabitEthernet8/3 unassigned YES unset up up

GigabitEthernet8/4 unassigned YES unset administratively down down

COR-01(config)#int g8/4

% This interface cannot be modified

Version 12.2(33)SXJ1

ip dhcp excluded-address 1.1.1.1

!

ip dhcp pool WiSM_service_Port

host 1.1.1.2 255.255.255.0

hardware-address 30e4.db38.a8c1

wism service-vlan 93

wism module 8 controller 1 allowed-vlan 90,800,810

wism module 8 controller 1 native-vlan 90

interface Vlan93

description WiSM service port do not route-Inner Chassis WiSM to Supervisor connection

ip address 1.1.1.1 255.255.255.0

COR-01#sh etherchannel summary

415 Po415(SU) - Te8/1(P)

Leo Laohoo · ‎08-16-2012

Your Service Port VLAN (93) is NOT ALLOWED.

manish_3191 · ‎08-16-2012

I have tried allowing vlan 93 but didnt work. I ahve run debug wism events on Cat6509 and seeing below logs:

Aug 17 02:44:26.035: WiSM-Evt:dman_show_module_status: Port Channel in the hwidb/fec goup is :1/415

Aug 17 02:44:26.799: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp: received a garp from 1.1.1.3/1.1.1.3
Aug 17 02:44:26.799: WiSM-Evt:dman_cntrl_db_search_by_mac: Found mac 30e4.db38.9981 for slot/port 8/1
Aug 17 02:44:26.799: WiSM-Evt:dman_reg_arp_added: cntrl 8/1 got an ip 1.1.1.3 30e4.db38.9981/30e4.db38.9981

Aug 17 02:44:40.019: WiSM-Evt:dman_reg_arp: received a garp from 1.1.1.2/1.1.1.2

Aug 17 02:44:42.127: WiSM-Evt:dman_proc_keepalive_tmr_handler: keepalive timer expired for 8/1
Aug 17 02:44:42.127: WiSM-Evt:dman_cntrl_db_search: something wrong 15

WiSM Controller 1 in Slot 8 configured with auto-lag

Operational Status of the Controller : Started KeepAlive
Service VLAN                         : 93
Service Port                         : 3
Service Port Mac Address             : 30e4.db38.9981
Service IP Address                   : 1.1.1.3
Management IP Address                : 0.0.0.0
Software Version                     :
Port Channel Number                  : 415
Allowed-vlan list                    : 90,93,800,810
Native VLAN ID                       : 90
WCP Keep Alive Missed                : 0

Leo Laohoo · ‎08-16-2012

Can you please post the output to the command "sh run | i wism module 8 controller 1"?

manish_3191 · ‎08-16-2012

COR-01#sh run | inc wism module 8 controller 1

wism module 8 controller 1 allowed-vlan 90,93,800,810

wism module 8 controller 1 native-vlan 90

Leo Laohoo · ‎08-16-2012

Forgot to ask if you can also post the output to the command "sh wism module 8 controller 1 status".

manish_3191 · ‎08-16-2012

COR-01#sh wism module 8 controller 1 status

WiSM Controller 1 in Slot 8 configured with auto-lag

Operational Status of the Controller : Started KeepAlive
Service VLAN                         : 93
Service Port                         : 3
Service Port Mac Address             : 30e4.db38.9981
Service IP Address                   : 1.1.1.3
Management IP Address                : 0.0.0.0
Software Version                     :
Port Channel Number                  : 415
Allowed-vlan list                    : 90,93,800,810
Native VLAN ID                       : 90
WCP Keep Alive Missed                : 0

Also providing Controller interface summary output. I have not used DHCP here. Assigned static ips.

(Cisco Controller) >show interface summary

Interface Name                   Port Vlan Id IP Address      Type    Ap Mgr Guest
-------------------------------- ---- -------- --------------- ------- ------ -----
management                       LAG untagged 10.76.12.12     Static Yes    No
service-port                     N/A N/A      1.1.1.3         Static No     No
virtual                          N/A N/A      2.2.2.2         Static No     No

Leo Laohoo · ‎08-16-2012

I cant modify those interfaces as seeing error " These interfaces can not be modified.

You are not allowed to modify the etherchannel ports. It's normal.

If you need to, you can only console into the WiSM 2 or you use the command to session in: session slot 8 process 1

Command needs to be run in the 6500.