cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2408
Views
5
Helpful
10
Replies

Frame-Relay with two Routers(frame-relay switches) in frame-relay cloud

daudparvez
Beginner
Beginner

Hi,

I am using following lab in GNS3 with two routes (frame-relay switches) in Frame-Relay cloud.

The interaces of these two routers connected to each other have been configured with nni type. However, my PVCs are not coming up.

nni.PNG

configurations of the R1 and R6 are as follows:

_______________________ R1_______________________

interface Serial0/0

no ip address

encapsulation frame-relay

serial restart_delay 0

clockrate 1008000

frame-relay lmi-type cisco

frame-relay intf-type dce

frame-relay route 103 interface Serial0/1 553

!

interface Serial0/1

no ip address

encapsulation frame-relay

shutdown

serial restart_delay 0

clockrate 1008000

no frame-relay inverse-arp

frame-relay lmi-type cisco

frame-relay intf-type nni

frame-relay route 551 interface Serial0/0 103

__________________________R6_______________________

!

interface Serial0/0

no ip address

encapsulation frame-relay

serial restart_delay 0

clockrate 1008000

frame-relay lmi-type cisco

frame-relay intf-type dce

frame-relay route 301 interface Serial0/1 551

!

interface Serial0/1

no ip address

encapsulation frame-relay

serial restart_delay 0

clockrate 1008000

no frame-relay inverse-arp

frame-relay lmi-type cisco

frame-relay intf-type nni

frame-relay route 553 interface Serial0/0 301

May be I am missing some command.Please help in resolving the issue.

Best Regards,

!

1 Accepted Solution

Accepted Solutions

Peter Paluch
Hall of Fame Cisco Employee Hall of Fame Cisco Employee
Hall of Fame Cisco Employee

Hello Daud,

After so many suggestions about corrections, I have lost track of what is your final state of configuration.

Please try to paste the following lines into your routers R1 and R6. They will reset the configuration of your S0/0 and S0/1 interfaces to default and configure them from scratch. If it does not help then please post the complete config of S0/0 and S0/1 interfaces from both R1 and R6. I have tested this configuration and it worked for me.

_______________________ R1_______________________

!

default interface Serial0/0

interface Serial0/0

no shutdown

no ip address

encapsulation frame-relay

frame-relay lmi-type cisco

frame-relay intf-type dce

frame-relay route 103 interface Serial0/1 553

!

default interface Serial0/1

interface Serial0/1

no shutdown

no ip address

encapsulation frame-relay

frame-relay lmi-type cisco

frame-relay intf-type nni

frame-relay route 553 interface Serial0/0 103

__________________________R6_______________________

!

default interface Serial0/0

interface Serial0/0

no shutdown

no ip address

encapsulation frame-relay

frame-relay lmi-type cisco

frame-relay intf-type dce

frame-relay route 301 interface Serial0/1 553

!

default interface Serial0/1

interface Serial0/1

no shutdown

no ip address

encapsulation frame-relay

frame-relay lmi-type cisco

frame-relay intf-type nni

frame-relay route 553 interface Serial0/0 301

Best regards,

Peter

P.S.: How did the thread with the OSPF over NBMA networks continue? I somehow lost track of it lately.

View solution in original post

10 Replies 10

cadet alain
Mentor
Mentor

Hi,

Can you try this:

R1

int s0/1

frame-relay route 553 interface Serial0/0 103

R2

int s0/1

frame-relay route 551 interface Serial0/0 301

Regards.

Alain

Don't forget to rate helpful posts.

Hi,

Still no working