cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1297
Views
0
Helpful
4
Replies

Hardware compatibility for Supervisor 2T

Sri v
Level 1
Level 1

i have a cisco 6509-E chassis with VS-SUP2T-10G with VS-F6K-MSFC5;VS-F6K-MSFC5.. does it support WS-X6716-10G-3C & WS-X6716-10G-3CXL ?

Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1203DEJL
4 24 CEF720 24 port 1000mb SFP WS-X6824-SFP SAL1826VJ4G
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1825UZQ4

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 001e.be82.39bc to 001e.be82.39d3 3.1 12.2(18r)S1 15.1(2)SY2 Ok
4 d072.dcfe.6f30 to d072.dcfe.6f47 2.3 12.2(18r)S1 15.1(2)SY2 Ok
5 503d.e514.001a to 503d.e514.0021 2.1 12.2(50r)SYS 15.1(2)SY2 Ok

Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Centralized Forwarding Card WS-F6700-CFC SAL1203DA99 4.0 Ok
4 Distributed Forwarding Card WS-F6K-DFC4-A SAL1826VJ4G 2.3 Ok
5 Policy Feature Card 4 VS-F6K-PFC4 SAL1825V8LE 2.1 Ok
5 CPU Daughterboard VS-F6K-MSFC5 SAL1824UUDC 3.0 Ok

1 Accepted Solution

Accepted Solutions

Yes the DFC4-A will support those cards doc attached , I didn't see you had the dfc4 in original post

View solution in original post

4 Replies 4

Mark Malone
VIP Alumni
VIP Alumni

You need a different daughter card as below

http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/catalyst-6500-series-supervisor-engine-2t/data_sheet_c78-648214.html

Table 5. Product Specifications

Product

Specifications

Chassis compatibility

• E-Series only: Cisco Catalyst 6503-E, 6504-E, 6506-E, 6509-E, 6509-V-E, 6513E

Switch fabric

• 2.08 Tbps Crossbar Switch Fabric with 26 Fabric Channels

Line-card compatibility

• WS-X6908-10G-2T, WS-X6908-10G-2TXL
• WS-X6824-SFP-2T, WS-X6824-SFP-2TXL
• WS-X6848-SFP-2T, WS-X6848-SFP-2TXL
• WS-X6848-TX-2T, WS-X6848-TX-2TXL
• WS-X6816-10T-2T, WS-X6816-10T-2TXL
• WS-X6816-10G-2T, WS-X6816-10G-2TXL
• WS-X6904-40G-2T, WS-X6904-40G-2TXL
• WS-X6704-10GE with CFC
• WS-X6724-SFP with CFC
• WS-X6748-SFP with CFC
• WS-X6748-GE-TX with CFC
• WS-X6148A-RJ-45, WS-X6148A-45AF, WS-X6148-FE-SFP, WS-X6148A-GE-TX, WS-X6148A-GE-45AF, WS-X6148E-GE-45AT

With a DFC4 or DFC4XL upgrade (WS-F6k-DFC4-A, WS-F6k-DFC4-AXL)

• WS-X6704-10GE
• WS-X6724-SFP
• WS-X6748-SFP
• WS-X6748-GE-TX

With a DFC4 or DFC4XL upgrade (WS-F6k-DFC4-E, WS-F6k-DFC4-EXL)

• WS-X6716-10G-3C, WS-X6716-10G-3CXL
• WS-X6716-10T-3C, WS-X6716-10T-3CXL

Hi Mark,

Thanks for the response

so u suggesting me to go for the below linecards as it will support with my supervisor?

• WS-X6716-10G-3C, WS-X6716-10G-3CXL

• WS-X6716-10T-3C, WS-X6716-10T-3CXL

Because supervisor running with PFC4 and one linecard already running with DFC-A

Yes the DFC4-A will support those cards doc attached , I didn't see you had the dfc4 in original post

Thanks mark..

Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G SAL1825UZQ4

Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
5 503d.e514.001a to 503d.e514.0021 2.1 12.2(50r)SYS 15.1(2)SY2 Ok

Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
5 Policy Feature Card 4 VS-F6K-PFC4 SAL1825V8LE 2.1 Ok
5 CPU Daughterboard VS-F6K-MSFC5 SAL1824UUDC 3.0 Ok

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco