ā12-24-2013 09:24 AM - edited ā03-07-2019 05:14 PM
Hi All,
I Want to configure IGMP snooping for IPTV server i configured IPTV vlan 30 all connectivity are okay just need commands for CORE switch CAT4507 And access switch 2960 only for IGMP.
IPTV-Server>>>>CAT4507+E>>>>>>2960PSL>>>>>STB+TV
Help will be appriciated
ā12-24-2013 09:48 AM
Are you only trying to do this within vlan 30 or do you want to route between vlans for the multicast stream ?
Jon
ā12-24-2013 10:58 AM
Thanks for the Quick Respo... BRO
for vlan 30 only will be best becoz i have vlans for CAM,DATA,VOICE below are the ports for IPTV in access switch.
interface gigabitEthernet 1/0/4
switchport mode access
switchport access vlan 30
spanning-tree portfast
no shut
exit
interface gigabitEthernet 1/0/5
switchport mode access
switchport access vlan 30
spanning-tree portfast
no shut
exit
interface gigabitEthernet 1/0/8
switchport mode access
switchport access vlan 30
spanning-tree portfast
no shut
exit
interface gigabitEthernet 1/0/12
switchport mode access
switchport access vlan 30
spanning-tree portfast
no shut
exit
Best Regards
ā12-24-2013 11:28 AM
If you are only doing it in one vlan then you need to have -
1) IGMP snooping enabled. This should be enabled by default
2) an IGMP snooping querier enabled so that the switch makes IGMP queries for that vlan. You only need to configure this on one switch. The 4500 would be a good choice. See this link for configuring it -
Jon
ā12-25-2013 06:28 AM
Thanks again ,,,
Problem is i am havin very basic knowldge abt switching what i understand.
1) i have to enable IGMP on spesfic vlan (ip igmp snooping vlan 30 ) on core switch
2) IGMP snooping querier (ip address of IPTV server ?)
3) no need to do anything in access switch my port configuration is okay ?
interface gigabitEthernet 1/0/12
switchport mode access
switchport access vlan 30
spanning-tree portfast
but if someone leave the stream the switch port will relax means gose normal immediately.
HAPPY CRISTMAS
ā12-25-2013 06:51 AM
1) You shouldn't have to as it should be enabled by default on both switches
2) The address should be the L3 vlan IP assigned to vlan 30 on the 4500.
3) your configuration is fine for the ports.
Happy Christmas to you as well
Jon
ā09-13-2014 03:36 AM
HI Mr JON,
I don,t know you are still available or not but i am facing a issue with same network i added one more ip head-end (DVB-Streamer) but traffic flooded on stb middleware ip head-end and all STB,s are in same vlan 30.
Streamer,s broadcast ip address range is
streamer1 -239.99.1.x
streamer2 -239.88.1.x
CORE1#sh ip igmp snooping querier
Vlan IP Address IGMP Version Port
-------------------------------------------------------------
30 10.121.55.1 v2 Switch
------------------------------------------------------------------------
CORE1#sh ip igmp snooping groups
Vlan Group Version Port List
---------------------------------------------------------
30 239.88.1.1 v2 Gi1/28, Gi2/13, Gi2/25
30 239.88.1.2 v2 Gi1/19, Gi2/16
30 239.88.2.1 v2 Gi1/1, Gi1/36, Gi2/19
30 239.88.3.1 v2 Gi2/18
30 239.88.4.1 v2 Gi1/6, Gi1/17, Gi1/29,
Gi1/34, Gi1/38, Gi1/46
30 239.99.1.32 v2 Gi1/9, Gi1/10, Gi1/13,
Gi1/15, Gi1/16, Gi1/22,
Gi1/25, Gi1/26, Gi1/27,
Gi1/30, Gi1/32, Gi1/41,
Gi1/42, Gi1/47, Gi1/48
30 239.99.1.33 v2 Gi1/24
30 239.99.1.34 v2 Gi1/2, Gi1/33, Gi2/14
30 239.99.1.35 v2 Gi1/7
30 239.99.1.50 v2 Gi1/4
30 239.99.1.52 v2 Gi1/21
30 239.99.2.32 v2 Gi1/45
30 239.99.2.36 v2 Gi1/5, Gi1/18, Gi1/20,
Gi1/31, Gi1/35, Gi2/1,
Gi2/6, Gi2/18
30 239.99.3.14 v2 Gi1/3, Gi1/14, Gi1/40,
Gi1/43
30 239.99.5.7 v2 Gi1/8
30 239.99.5.21 v2 Gi2/4
30 239.255.255.250 v2 Gi1/1, Gi1/2, Gi1/3,
Gi1/4, Gi1/5, Gi1/6,
Gi1/7, Gi1/8, Gi1/9,
Gi1/10, Gi1/13, Gi1/14,
Gi1/15, Gi1/16, Gi1/17,
Gi1/18, Gi1/19, Gi1/20,
Gi1/21, Gi1/22, Gi1/24,
Gi1/25, Gi1/26, Gi1/27,
Gi1/28, Gi1/29, Gi1/30,
Gi1/31, Gi1/32, Gi1/33,
Gi1/34, Gi1/35, Gi1/36,
Gi1/38, Gi1/40, Gi1/41,
Gi1/42, Gi1/43, Gi1/45,
Gi1/46, Gi1/47, Gi1/48,
Gi2/1, Gi2/4, Gi2/6,
Gi2/13, Gi2/14, Gi2/16,
Gi2/18, Gi2/19, Gi2/25
=======================================================
CORE1#sh ip igmp snooping mrouter
Vlan ports
---- -----
30 Switch
=====================================================
CORE1#sh processes cpu history
211121121213221111111121211121211212131111111222422232323221
683419325641925654565575945434483352607645454641216617190956
100
90
80
70
60
50 *
40 * ** *
30 * * ** * * * * * ********* * *******
20 ** ** *** ****** ******* * * ** ******* * * ***************************
10 ########################################################################
0....5....1....1....2....2....3....3....4....4....5....5....6....6....7.
0 5 0 5 0 5 0 5 0 5 0 5 0
CPU% per hour (last 72 hours)
* = maximum CPU% # = average CPU%
Any Help
Regards
ā11-20-2014 01:35 PM
Hi sheraz
i hope you are fine
sheraz now i have new IPTV project for hotel
but i'm just want to ask you about client interface on the access switch speed,
all my access switches are WS-C2960+48PST-S
and core switch is CISCO 3650
the interface speed 100MB so there is any problem with it or now ?
and what about the interfaces bandwidth in your access switches
please answer me because it's major case for my project
have nice day
thanks
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: