12-08-2020 10:18 PM
Hi!
I am getting errors on LAN & WAN interfaces. What can be the reason?
WAN Interface Show Interfaces Output: Also 2 Sub-Interfaces are configured on Gig 0/0 (NAT Outside Interface)
Core-Router#show int gig 0/0
GigabitEthernet0/0 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is 68bd.abbd.d720 (bia 68bd.abbd.d720)
Description: WAN
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive not set
Full-duplex, 1000Mb/s, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 7w0d
Input queue: 0/75/8/14951 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 2079000 bits/sec, 326 packets/sec
5 minute output rate 798000 bits/sec, 256 packets/sec
476894658 packets input, 2224149772 bytes, 1161 no buffer
Received 9134960 broadcasts, 0 runts, 0 giants, 54 throttles
7473 input errors, 0 CRC, 0 frame, 7473 overrun, 0 ignored
0 watchdog, 12136746 multicast, 0 pause input
0 input packets with dribble condition detected
2850543739 packets output, 2611710532 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
143621 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
LAN Interface: 2-Sub-Interfaces are configured on LAN Segment:
Core-Router#show int gig 0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is 68bd.abbd.d721 (bia 68bd.abbd.d721)
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive not set
Full-duplex, 1000Mb/s, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 7w0d
Input queue: 0/75/1173/1874 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Class-based queueing
Output queue: 0/1000/0 (size/max total/drops)
5 minute input rate 746000 bits/sec, 249 packets/sec
5 minute output rate 1856000 bits/sec, 308 packets/sec
2912456875 packets input, 861332191 bytes, 885 no buffer
Received 31655591 broadcasts, 0 runts, 0 giants, 42 throttles
2349 input errors, 0 CRC, 0 frame, 2349 overrun, 0 ignored
0 watchdog, 35341194 multicast, 0 pause input
0 input packets with dribble condition detected
467413018 packets output, 735028861 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
151524 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Solved! Go to Solution.
12-08-2020 11:21 PM
- Check the resolving-answer from this thread :
https://community.cisco.com/t5/small-business-routers/interface-input-errors/td-p/2964643
M.
12-08-2020 11:21 PM
- Check the resolving-answer from this thread :
https://community.cisco.com/t5/small-business-routers/interface-input-errors/td-p/2964643
M.
12-08-2020 11:55 PM
Hello,
--> 143621 unknown protocol drops
Try and turn off CDP (no cdp run), unknown protocol drops can be anything including CDP.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide