cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2276
Views
0
Helpful
2
Replies

InterVlan routing in Catalyst WS-C2960S-48TD-L

frank.liu
Level 1
Level 1

Hi,

Based on this document:

http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/software/release/12.2_55_se/configuration/guide/swipstatrout.html

and this discussion https://supportforums.cisco.com/thread/2084228 Intervlan routing is available in 2960 as of 12.2.55.

I have 12.2.55se6 but "ip routing" doesn't exist. Any thoughts.

sw01(config)#ip routing

                     ^

% Invalid input detected at '^' marker.

sh ver

Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE6, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Mon 23-Jul-12 13:45 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x01B00000

ROM: Bootstrap program is Alpha board boot loader

BOOTLDR: C2960S Boot Loader (C2960S-HBOOT-M) Version 12.2(53r)SE, RELEASE SOFTWARE (fc3)

sw01 uptime is 3 hours, 17 minutes

System returned to ROM by power-on

System image file is "flash:/c2960s-universalk9-mz.122-55.SE6.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco WS-C2960S-48TD-L (PowerPC) processor (revision E0) with 131072K bytes of memory.

Processor board ID FOC1535Z0W7

Last reset from power-on

2 Virtual Ethernet interfaces

1 FastEthernet interface

50 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : xx

Motherboard assembly number     : xx

Power supply part number        : xx

Motherboard serial number       : xx

Power supply serial number      : xx

Model revision number           : E0

Motherboard revision number     : A0

Model number                    : WS-C2960S-48TD-L

Daughterboard assembly number   : xx

Daughterboard serial number     : xx

System serial number            : xx

Top Assembly Part Number        : 800-30925-03

Top Assembly Revision Number    : A0

Version ID                      : V03

CLEI Code Number                : xx

Daughterboard revision number   : A0

Hardware Board Revision Number  : 0x01

Switch Ports Model              SW Version            SW Image

------ ----- -----              ----------            ----------

*    1 52    WS-C2960S-48TD-L   12.2(55)SE6           C2960S-UNIVERSALK9-M

Configuration register is 0xF

2 Accepted Solutions

Accepted Solutions

first run "sdm prefer lanbase-routing" in config mode, reload the switch and try to enable routing again: http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/software/release/12.2_55_se/configuration/guide/swipstatrout.html

View solution in original post

ALIAOF_
Level 6
Level 6

Well I always thought that it is only Layer 2 switch but apparently with a Lanbase license you can do it as of 12.2(55)SE.  Have you first tried running "sdm prefer lanbase-routing" command first, then you'll need to save and reboot.  Once back up you'll hvae access to the ip routing command.

Now keep in mind the bug CSCtj37604. But I think you are running the newer IOS so it might not apply to your IOS.

View solution in original post

2 Replies 2

first run "sdm prefer lanbase-routing" in config mode, reload the switch and try to enable routing again: http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/software/release/12.2_55_se/configuration/guide/swipstatrout.html

ALIAOF_
Level 6
Level 6

Well I always thought that it is only Layer 2 switch but apparently with a Lanbase license you can do it as of 12.2(55)SE.  Have you first tried running "sdm prefer lanbase-routing" command first, then you'll need to save and reboot.  Once back up you'll hvae access to the ip routing command.

Now keep in mind the bug CSCtj37604. But I think you are running the newer IOS so it might not apply to your IOS.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Review Cisco Networking products for a $25 gift card