10-04-2010 06:31 AM - edited 03-06-2019 01:18 PM
Hello!
I am trying to configure multicast streaming. I configured successfully streaming, where server and client are in one VLAN, all is ok, but now I'm trying to stream to different VLANS. I have catalyst 3750 switch and two hosts, one streams, second listens. I configured 3750 like in manual, but can't understand why i don't see the image on client, because mvr members are active.
Network scheme: (client-VLAN10)---/gi1/0/2/---(3750)---/gi1/0/4/---(server-VLAN20)
My switch current config is above:
Current configuration : 3714 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname cisco3
!
boot-start-marker
boot-end-marker
!
enable secret ***
enable password ***
!
no aaa new-model
switch 1 provision ws-c3750g-24t
system mtu routing 1500
vtp mode transparent
ip subnet-zero
ip routing
!
!
ip igmp snooping querier
ip igmp profile 1
permit
range 227.24.1.250 227.24.1.250
!
mvr vlan 20
mvr group 227.24.1.250
mvr
!
crypto pki trustpoint TP-self-signed-1552593280
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1552593280
revocation-check none
rsakeypair TP-self-signed-1552593280
!
!
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
vlan 10
name IPTV-CLIENTS
!
vlan 20
name IPTV-Server
!
!
!
!
interface GigabitEthernet1/0/1
!
interface GigabitEthernet1/0/2
switchport access vlan 10
switchport mode access
mvr type receiver
!
interface GigabitEthernet1/0/3
!
interface GigabitEthernet1/0/4
switchport access vlan 20
switchport mode access
mvr type source
!
//nothing configured on interfaces 5 - 24
!
interface GigabitEthernet1/0/24
!
interface Vlan1
ip address 83.241.1.1 255.255.255.0
!
interface Vlan10
description IPTV-clients
ip address 83.241.10.1 255.255.255.0
ip pim dense-mode
!
interface Vlan20
description IPTV-Server
ip address 83.241.20.1 255.255.255.0
ip pim dense-mode
!
ip classless
ip http server
ip http secure-server
!
!
!
=====================
#show mvr
MVR Running: TRUE
MVR multicast VLAN: 20
MVR Max Multicast Groups: 256
MVR Current multicast groups: 1
MVR Global query response time: 5 (tenths of sec)
MVR Mode: compatible
=====================
#show mvr interface
Port Type Status Immediate Leave
---- ---- ------ ---------------
Gi1/0/2 RECEIVER ACTIVE/UP DISABLED
Gi1/0/4 SOURCE ACTIVE/UP DISABLED
=====================
#show mvr members
MVR Group IP Status Members
------------ ------ -------
227.024.001.250 ACTIVE Gi1/0/2(d), Gi1/0/4(s)
======================
Any suggestions? Thanks a lot for your answers!
10-04-2010 09:40 PM
Hello,
Just I found in the following Cisco document and already one post in Cisco support community like Multicasting across Vlans. May be you will get some idea.
https://supportforums.cisco.com/message/3113275
MB.Ahamed
10-05-2010 12:26 AM
Thank you, but I have read it many times and not only this chapter in this manual, but there wasn't working solutions for me.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide