logs time incoreect

[Manish Manwal]

in our c3850 switch logs time is different from our local time. i have already set the timestamp service date time local but is not working. my current time is 11.22 and use timezon utc 5 30

example :

Oct  3 05:52:35.163: [IDB Te1/0/7 UDRUnn] CSTATE_REQ: Entry, requested state: D
Oct  3 05:52:35.164: [IDB Te1/0/7 UDRUnn] CSTATE_REQ: starting ctimer (2000)
Oct  3 05:52:35.164: [IDB Te1/0/7 DURUnn] CSTATE_REQ: state assign
Oct  3 05:52:35.164: [IDB Te1/0/7 DURUnn] CSTATE_REQ: state assign
Oct  3 05:52:35.164: [IDB Te1/0/7 DURUnn] LSTATE_REQ: Entry
Oct  3 05:52:35.164: [IDB Te1/0/7 DURUnn] LSTATE_REQ: Exit
Oct  3 05:52:35.164: [IDB Te1/0/7 DURUnn] CSTATE_REQ: Exit
Oct  3 05:52:36.443: [IDB Te1/0/8 UDRUYY] LSTATE_REQ: Entry
Oct  3 05:52:36.443: [IDB Te1/0/8 UDRUYY] LSTATE_REQ: timers not running
Oct  3 05:52:36.443: [IDB Te1/0/8 UDRUYY] LSTATE_REQ: starting lineproto timer
Oct  3 05:52:36.443: [IDB Te1/0/8 UDRUYY] LSTATE_REQ: delay 1000
Oct  3 05:52:36.443: [IDB Te1/0/8 UDRUYY] LSTATE_REQ: Exit
Oct  3 05:52:36.447: [IDB Te1/0/8 UDRUYY] CSTATE_REQ: Entry, requested state: D
Oct  3 05:52:36.448: [IDB Te1/0/8 UDRUYY] CSTATE_REQ: starting ctimer (2000)
Oct  3 05:52:36.448: [IDB Te1/0/8 DURUYY] CSTATE_REQ: state assign
Oct  3 05:52:36.448: [IDB Te1/0/8 DURUYY] CSTATE_REQ: state assign
Oct  3 05:52:36.448: [IDB Te1/0/8 DURUYY] LSTATE_REQ: Entry
Oct  3 05:52:36.448: [IDB Te1/0/8 DURUYY] LSTATE_REQ: Exit
Oct  3 05:52:36.448: [IDB Te1/0/8 DURUYY] CSTATE_REQ: Exit
Oct  3 05:52:37.162: [IDB Te1/0/7 DURUnn] CSTATE_TMR: Entry
Oct  3 05:52:37.162: [IDB Te1/0/7 DURUnn] CSTATE_TMR: netidb=Te1/0/7, linestate: n
Oct  3 05:52:37.162: [IDB Te1/0/7 DURUnn] LSTATE_REQ: Entry
Oct  3 05:52:37.162: [IDB Te1/0/7 DURUnn] LSTATE_REQ: timers not running
Oct  3 05:52:37.163: [IDB Te1/0/7 DURUnn] LSTATE_REQ: Exit
Oct  3 05:52:37.163: [IDB Te1/0/7 DURUnn] CSTATE_TMR: transition detected
Oct  3 11:22:37: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/0/7, changed state to down
Oct  3 05:52:37.163: [IDB Te1/0/7 DURUnn] TRANS_ADJ: Entry
Oct  3 05:52:37.164: [IDB Te1/0/7 DURUnn] TRANS_ADJ: Exit
Oct  3 05:52:37.164: [IDB Te1/0/7 DURUnn] CSTATE_TMR: Exit
Oct  3 05:52:37.442: [IDB Te1/0/8 DURUYY] LSTATE_TMR: Entry
Oct  3 05:52:37.442: [IDB Te1/0/8 DURUYY] LSTATE_TMR: not spoofing, current state: n
Oct  3 11:22:37: %LINEPROTO-5-UPDOWN: Line protocol on Interface TenGigabitEthernet1/0/8, changed state to down
Oct  3 05:52:37.442: [IDB Te1/0/8 DURUYY] LSTATE_TMR: Exit
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUYY] CSTATE_TMR: Entry
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUYY] CSTATE_TMR: netidb=Te1/0/8, linestate: n
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUYY] LSTATE_REQ: Entry
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUYY] LSTATE_REQ: timers not running
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUYY] LSTATE_REQ: Exit
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUYY] CSTATE_TMR: transition detected
Oct  3 11:22:38: %LINK-3-UPDOWN: Interface TenGigabitEthernet1/0/8, changed state to down
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUnY] TRANS_ADJ: Entry
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUnn] TRANS_ADJ: propagating change to subifs
Oct  3 05:52:38.442: [IDB Te1/0/8 DURUnn] TRANS_ADJ: Exit
Oct  3 05:52:38.443: [IDB Te1/0/8 DURUnn] CSTATE_TMR: Exit
Oct  3 05:53:40.694: %NTP : Drift string saved to persistent data: NTPv4_Drift=0.0

[Georg Pauwen]

Hello,

--> Oct 3 05:53:40.694: %NTP : Drift string saved to persistent data: NTPv4_Drift=0.0

Do you have NTP configured on your switch ? Post the full config, as well as the output of 'show clock'...

[Manish Manwal]

sh run configuration and sh clock
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.10.03 13:38:29 =~=~=~=~=~=~=~=~=~=~=~=
login as: admin
Using keyboard-interactive authentication.
Password:
CSW1.PLANT1>en
Password:
SW1.PLANT1#terminal l
CSW1.PLANT1#terminal length 0

Building configuration...

Current configuration : 6884 bytes
!
! Last configuration change at 14:54:15 UTC Wed Sep 26 2018 by admin
! NVRAM config last updated at 14:44:08 UTC Wed Sep 26 2018 by admin
!
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime localtime
service password-encryption
service compress-config
!
hostname CSW1.PLANT1
!
boot-start-marker
boot-end-marker
!
!
vrf definition Mgmt-vrf
!
address-family ipv4
exit-address-family
!
address-family ipv6
exit-address-family
!
enable secret level 2 5 **********
enable password 7 *********
!
username Admin password 7 ****************
username Akums privilege 0 password 7 ************
no aaa new-model
clock timezone UTC 5 30
clock calendar-valid
switch 1 provision ws-c3850-24xs
!
!
!
!
!
coap http enable
!
!
!
!
!
!
ip routing
no ip cef optimize neighbor resolution
!
ip domain-name Akums
ip host time.zone 10.10.100.101
!
!
qos queue-softmax-multiplier 100
udld enable

!
!
errdisable recovery cause udld
errdisable recovery cause bpduguard
errdisable recovery cause security-violation
errdisable recovery cause channel-misconfig
errdisable recovery cause pagp-flap
errdisable recovery cause dtp-flap
errdisable recovery cause link-flap
errdisable recovery cause sfp-config-mismatch
errdisable recovery cause gbic-invalid
errdisable recovery cause l2ptguard
errdisable recovery cause psecure-violation
errdisable recovery cause port-mode-failure
errdisable recovery cause dhcp-rate-limit
errdisable recovery cause pppoe-ia-rate-limit
errdisable recovery cause mac-limit
errdisable recovery cause vmps
errdisable recovery cause storm-control
errdisable recovery cause inline-power
errdisable recovery cause arp-inspection
errdisable recovery cause loopback
errdisable recovery cause psp
errdisable recovery interval 180
diagnostic bootup level minimal
!
spanning-tree mode rapid-pvst
spanning-tree portfast default
spanning-tree extend system-id
no spanning-tree vlan 20
hw-switch switch 1 logging onboard message level 3
!
redundancy
mode sso
!
!
!
class-map match-any non-client-nrt-class
!
policy-map port_child_policy
class non-client-nrt-class
bandwidth remaining ratio 10
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface Loopback1
ip address 10.255.255.254 255.255.255.255
!
interface GigabitEthernet0/0
vrf forwarding Mgmt-vrf
no ip address
negotiation auto
!
interface TenGigabitEthernet1/0/1
switchport mode access
!
interface TenGigabitEthernet1/0/2
description link to assam vlan 80
switchport mode trunk
!
interface TenGigabitEthernet1/0/3
description LINK TO HRD
switchport mode trunk
speed 100
duplex full
!
interface TenGigabitEthernet1/0/4
description link to Asam
switchport mode trunk
!
interface TenGigabitEthernet1/0/5
description cyberoam port E
switchport mode access
!
interface TenGigabitEthernet1/0/6
description cyberoam port H
no switchport

!
interface TenGigabitEthernet1/0/7
description cyberoam2 port E
switchport mode access
!
interface TenGigabitEthernet1/0/8
description cyberoam2 port H
switchport mode trunk
!
interface TenGigabitEthernet1/0/9
!
interface TenGigabitEthernet1/0/10
!
interface TenGigabitEthernet1/0/11
!
interface TenGigabitEthernet1/0/12
!
interface TenGigabitEthernet1/0/13
!
interface TenGigabitEthernet1/0/14
!
interface TenGigabitEthernet1/0/15
switchport mode access
!
interface TenGigabitEthernet1/0/16
!
interface TenGigabitEthernet1/0/17
!
interface TenGigabitEthernet1/0/18
description PLANT-1 SWITCH
switchport mode trunk
!
interface TenGigabitEthernet1/0/19
description PLANT-2 S.ROOM
switchport mode trunk
!
interface TenGigabitEthernet1/0/20
description PLANT-1 BETA S.ROOM
switchport mode trunk
!
interface TenGigabitEthernet1/0/21
description LINK TO PLANT-4
switchport mode trunk
!
interface TenGigabitEthernet1/0/22
description LINK TO PLANT-3
switchport mode trunk
!
interface TenGigabitEthernet1/0/23
description LINK TO MAXCURE
switchport mode trunk
!
interface TenGigabitEthernet1/0/24
description LINK TO PURE&CURE
switchport mode trunk
!
interface TenGigabitEthernet1/1/1
!
interface TenGigabitEthernet1/1/2
!
interface TenGigabitEthernet1/1/3
!
interface TenGigabitEthernet1/1/4
!
interface TenGigabitEthernet1/1/5
!
interface TenGigabitEthernet1/1/6
!
interface TenGigabitEthernet1/1/7
!
interface TenGigabitEthernet1/1/8
!
interface FortyGigabitEthernet1/1/1
!
interface FortyGigabitEthernet1/1/2
!

interface Vlan2
no ip address
!

!

!
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
!

!
snmp-server community Core_logs RW
!
!
!
line con 0
login local
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login local
line vty 5 15
login
!
!
monitor session 2 source interface Te1/0/5 - 6
monitor session 2 destination interface Te1/0/7
ntp broadcastdelay 9999
ntp master
wsma agent exec
profile httplistener
profile httpslistener
!
wsma agent config
profile httplistener
profile httpslistener
!
wsma agent filesys
profile httplistener
profile httpslistener
!
wsma agent notify
profile httplistener
profile httpslistener
!
!
wsma profile listener httplistener
transport http
!
wsma profile listener httpslistener
transport https
mac address-table static 7a04.1918.19a7 vlan 1 drop
mac address-table static 4c11.bfb0.985d vlan 1 drop
!
ap group default-group
end

CSW1.PLANT1#sh clo
CSW1.PLANT1#sh clock
13:40:20.133 UTC Wed Oct 3 2018
CSW1.PLANT1#exit

[Alex Pfeil]

Please check this out.

https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-2/system_management/command/reference/b_sysman_cr42crs/b_sysman_cr42crs_chapter_0100.pdf#page7

Please rate helpful posts.

[Alex Pfeil]

It is a best practice to setup an NTP server to synchronize time across all devices as well.