Hi ,I have a Cisco catalyst 6513 with sup720-3bxl and WS-X6724-SFP modules , the switch was working fine until yesterday ,but after a maintenance the modue WS-X6724-SFP failed to bring online , the error code is (Module Failed SCP dnld) does it mean the module has hardware problem or i need to replace it ?
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
ios version
s72033-adventerprisek9_wan-vz.122-33.SXH7.bin
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
show module
Mod Ports Card Type Model
--- ----- -------------------------------------- ------------------
5 6 Firewall Module WS-SVC-FWM-1
7 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL
9 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
11 24 CEF720 24 port 1000mb SFP WS-X6724-SFP
13 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
5 0011.2000.d974 to 0011.2000.d97b 3.2 7.2(1) 4.1(6) Ok
7 001a.a22d.5728 to 001a.a22d.572b 5.7 8.5(2) 12.2(33)SXH7 Ok
9 0027.0dcb.b464 to 0027.0dcb.b47b 4.3 12.2(18r)S1 12.2(33)SXH7 Ok
11 0027.0d95.d6a8 to 0027.0d95.d6bf 4.2 Unknown Unknown PwrDown
13 0027.0da5.0058 to 0027.0da5.0087 7.3 7.2(1) 8.7(0.22)BUB Ok
Mod Sub-Module Model Hw Status
---- --------------------------- ------------------ ----------- -------
7 Policy Feature Card 3 WS-F6K-PFC3BXL 1.9 Ok
7 MSFC3 Daughterboard WS-SUP720 3.2 Ok
9 Centralized Forwarding Card WS-F6700-CFC 4.1 Ok
11 Centralized Forwarding Card WS-F6700-CFC 4.1 PwrDown
Mod Online Diag Status
---- -------------------
5 Pass
7 Pass
9 Pass
11 Not Applicable
13 Pass
----------------------------------------------------------------------------------------------------------------------------------
console log files
1d03h: %ONLINE-SP-6-TIMER: Module 11, Proc. 0. Failed to bring online because of timer event
1d03h: %C6KPWR-SP-4-DISABLED: power to module in slot 11 set off (Module Failed SCP dnld)
-------------------------------------------------
show power
system power redundancy mode = redundant
system power total = 3795.12 Watts (90.36 Amps @ 42V)
system power used = 1355.76 Watts (32.28 Amps @ 42V)
system power available = 2439.36 Watts (58.08 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-4000W-INT 3795.12 90.36 OK OK on
2 WS-CAC-4000W-INT 3795.12 90.36 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6K-13SLT-FAN2 298.20 7.10 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
5 WS-SVC-FWM-1 171.78 4.09 171.78 4.09 on on
7 WS-SUP720-3BXL 328.44 7.82 328.44 7.82 on on
8 (Redundant Sup) - - 328.44 7.82 - -
9 WS-X6724-SFP 125.16 2.98 125.16 2.98 on on
11 WS-X6724-SFP 125.16 2.98 - - on off (Diagnostic Failure)
13 WS-X6148-GE-TX 103.74 2.47 103.74 2.47 on on
------------------------
diagnostic start module 11 test complete
1d18h: %DIAG-SP-6-TEST_RUNNING: Module 11: Running TestLoopback{ID=2} ...
1d18h: %DIAG-SP-3-TEST_FAIL: Module 11: TestLoopback{ID=2} has failed. Error code = 0x16
1d18h: %DIAG-SP-6-TEST_RUNNING: Module 11: Running TestTxPathMonitoring{ID=3} ...
1d18h: %DIAG-SP-6-TEST_OK: Module 11: TestTxPathMonitoring{ID=3} has completed successfully
1d18h: %DIAG-SP-6-TEST_RUNNING: Module 11: Running TestL3VlanMet{ID=5} ...
1d18h: %DIAG-SP-3-DIAG_RUNNING: Module 11: Diagnostic is currently running
1d18h: %DIAG-SP-3-TEST_FAIL: Module 11: TestL3VlanMet{ID=5} has failed. Error code = 0x1C
1d18h: %DIAG-SP-6-TEST_RUNNING: Module 11: Running TestIngressSpan{ID=6} ...
1d18h: %DIAG-SP-3-TEST_FAIL: Module 11: TestIngressSpan{ID=6} has failed. Error code = 0x1C
1d18h: %DIAG-SP-6-TEST_RUNNING: Module 11: Running TestEgressSpan{ID=7} ...
1d18h: %DIAG-SP-3-TEST_FAIL: Module 11: TestEgressSpan{ID=7} has failed. Error code = 0x16
1d18h: %DIAG-SP-6-TEST_RUNNING: Module 11: Running TestFirmwareDiagStatus{ID=10} ...
1d18h: %OIR-SP-3-PWRCYCLE: Card in module 11, is being power-cycled off (Diagnostic Failure)
1d18h: %C6KPWR-SP-4-DISABLED: power to module in slot 11 set off (Diagnostic Failure)
1d18h: %DIAG-SP-3-TEST_FAIL: Module 11: TestFirmwareDiagStatus{ID=10} has failed. Error code = 0x7A
--------------------------------
