09-02-2012 10:26 PM - edited 03-07-2019 08:39 AM
I setup a GRE tunnel between two cisco 1800 & 1900 routers. I can't received multicast.
Here is a copy of my configs:
R3#
Building configuration...
Current configuration : 1238 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R3
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
!
no aaa new-model
dot11 syslog
ip source-route
!
ip cef
ip multicast-routing
no ipv6 cef
!
multilink bundle-name authenticated
!
archive
log config
hidekeys
!
interface Loopback0
ip address 10.0.0.3 255.255.255.255
!
interface Tunnel0
ip address 192.168.24.2 255.255.255.252
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.0.0.1
!
interface FastEthernet0/0
ip address 10.0.3.1 255.255.255.0
ip pim sparse-mode
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 192.168.23.2 255.255.255.252
ip pim sparse-mode
duplex auto
speed auto
!
interface Serial0/0/0
no ip address
shutdown
no fair-queue
clock rate 2000000
!
router eigrp 1
network 10.0.0.3 0.0.0.0
network 10.0.3.1 0.0.0.0
network 192.168.23.2 0.0.0.0
no auto-summary
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
control-plane
!
line con 0
line aux 0
line vty 0 4
exec-timeout 5 0
privilege level 15
no login
!
scheduler allocate 20000 1000
end
R2#
Building configuration...
Current configuration : 1029 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R2
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
!
no aaa new-model
dot11 syslog
ip source-route
!
ip cef
ip multicast-routing
no ipv6 cef
!
multilink bundle-name authenticated
!
archive
log config
hidekeys
!
interface Loopback0
ip address 10.0.0.2 255.255.255.255
!
interface FastEthernet0/0
ip address 192.168.23.1 255.255.255.252
ip pim sparse-mode
duplex auto
speed auto
!
interface FastEthernet0/1
ip address 192.168.12.2 255.255.255.252
ip pim sparse-mode
duplex auto
speed auto
!
router eigrp 1
network 10.0.0.2 0.0.0.0
network 192.168.12.2 0.0.0.0
network 192.168.23.1 0.0.0.0
no auto-summary
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
control-plane
!
line con 0
line aux 0
line vty 0 4
exec-timeout 5 0
privilege level 15
no login
!
scheduler allocate 20000 1000
end
R1#
Building configuration...
Current configuration : 1316 bytes
!
! Last configuration change at 04:25:02 UTC Mon Sep 3 2012
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname R1
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
no ipv6 cef
ip source-route
ip cef
!
ip multicast-routing
!
multilink bundle-name authenticated
!
crypto pki token default removal timeout 0
!
license udi pid CISCO1921/K9 sn FGL152624YV
!
interface Loopback0
ip address 10.0.0.1 255.255.255.255
!
interface Tunnel0
ip address 192.168.24.1 255.255.255.252
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.0.0.3
!
interface GigabitEthernet0/0
ip address 192.168.12.1 255.255.255.252
ip pim sparse-mode
duplex auto
speed auto
!
interface GigabitEthernet0/1
ip address 10.0.1.1 255.255.255.0
ip pim sparse-mode
duplex auto
speed auto
!
router eigrp 1
network 10.0.0.1 0.0.0.0
network 10.0.1.1 0.0.0.0
network 192.168.12.1 0.0.0.0
!
ip forward-protocol nd
!
ip mroute 10.0.3.0 255.255.255.0 Tunnel0
ip mroute 10.0.0.3 255.255.255.255 Tunnel0
no ip http server
no ip http secure-server
!
control-plane
!
line con 0
line aux 0
line vty 0 4
exec-timeout 5 0
privilege level 15
no login
transport input all
!
scheduler allocate 20000 1000
end
R3#
Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3)
R2#
Cisco IOS Software, 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3)
R1#
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(3)T1, RELEASE SOFTWARE (fc2)
Thank you very much
09-02-2012 11:02 PM
now, i changed configure:
R1(config)#no ip mroute 10.0.3.0 255.255.255.0 Tunnel0
R1(config)#no ip mroute 10.0.0.3 255.255.255.255 Tunnel0
R1(config)#ip pim rp-address 10.0.0.2
R2(config)#ip pim rp-address 10.0.0.2
R3(config)#ip pim rp-address 10.0.0.2
receiver can received. but not pass through gre tunnel ?
R1#sho ip mro 239.12.9.3
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
V - RD & Vector, v - Vector
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 239.12.9.3), 02:35:44/stopped, RP 10.0.0.2, flags: SJC
Incoming interface: GigabitEthernet0/0, RPF nbr 192.168.12.2
Outgoing interface list:
GigabitEthernet0/1, Forward/Sparse, 00:03:55/00:02:09
(10.0.3.2, 239.12.9.3), 00:15:30/00:02:04, flags: JT
Incoming interface: GigabitEthernet0/0, RPF nbr 192.168.12.2
Outgoing interface list:
GigabitEthernet0/1, Forward/Sparse, 00:03:55/00:02:09
09-02-2012 11:28 PM
Study it once, Let me know if you are facing the issue then
http://www.cisco.com/en/US/tech/tk828/technologies_configuration_example09186a00801a5aa2.shtml
Regards
Inder
Blogs:
09-03-2012 01:16 AM
now I no configuration about multicast on R2.
and only enable ip pim sparse-mode on Tunnel GRE and LAN interface of R1 and R3.
R3#
!
ip multicast-routing
!
interface Loopback0
ip address 10.0.0.3 255.255.255.255
!
interface Tunnel0
ip address 192.168.24.2 255.255.255.252
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.0.0.1
!
interface FastEthernet0/0
description to source multicast
ip address 10.0.3.1 255.255.255.0
ip pim sparse-mode
!
interface FastEthernet0/1
ip address 192.168.23.2 255.255.255.252
!
router eigrp 1
network 10.0.0.3 0.0.0.0
network 10.0.3.1 0.0.0.0
network 192.168.23.2 0.0.0.0
no auto-summary
R2#
!
interface Loopback0
ip address 10.0.0.2 255.255.255.255
!
interface FastEthernet0/0
ip address 192.168.23.1 255.255.255.252
!
interface FastEthernet0/1
ip address 192.168.12.2 255.255.255.252
!
router eigrp 1
network 10.0.0.2 0.0.0.0
network 192.168.12.2 0.0.0.0
network 192.168.23.1 0.0.0.0
no auto-summary
R1#
!
ip multicast-routing
!
interface Loopback0
ip address 10.0.0.1 255.255.255.255
!
interface Tunnel0
ip address 192.168.24.1 255.255.255.252
ip pim sparse-mode
tunnel source Loopback0
tunnel destination 10.0.0.3
!
interface GigabitEthernet0/0
ip address 192.168.12.1 255.255.255.252
!
interface GigabitEthernet0/1
ip address 10.0.1.1 255.255.255.0
ip pim sparse-mode
!
router eigrp 1
network 10.0.0.1 0.0.0.0
network 10.0.1.1 0.0.0.0
network 192.168.12.1 0.0.0.0
!
ip mroute 10.0.3.0 255.255.255.0 Tunnel0
It worked. multicast can passed GRE Tunnel, but I must use 224.0.1.40 for source. I can't change to other IP. What should I do ? (I use 239.x.x.x in real network.)
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: