cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2100
Views
0
Helpful
3
Replies

% NBAR Error: symbol addition0:16:11.251: %NBAR-2-NOMEMORY: No memory available for StILE lmalloc -Traceback

Hi Friends ,

I am planning to configure NAT for giving internet access to our local LAN users . while configuring NAT i am receiving the following errors . kindly give your valuable support to get out of this problem.

i am pasteing the error for your reference

NBAR Error: symbol addition

% NBAR Error: symbol addition0:16:11

.251: %NBAR-2-NOMEMOR

Y: No memory available for StILE lmalloc

-Traceback= 2386C9ECz 2385C11Cz 2385C47Cz 2385C694z 23869E70z 2386A020z 2386E0E8z 238487F0z 2388BE40z 2388C1F8z 238C9B00z 22E49A74z 22E4C410z 22502F28z 22509600z 2251AAB8z

% NBAR Error: symbol addition

% NBAR Error: symbol addition

% NBAR Error: symbol addition

% NBAR Error: symbol addition

% NBAR Error: symbol addition

% NBAR Error: symbol addition

% NBAR Error: symbol addition

% NBAR Error: symbol addition

3 Replies 3

cadet alain
VIP Alumni
VIP Alumni

Hi,

you  haven't got enough memory:

NBAR Error: symbol addition

% NBAR Error: symbol addition0:16:11

.251: %NBAR-2-NOMEMOR

Y: No memory available for StILE lmalloc

Can you provide the sh version output to get the model and available RAM

Regards

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.

HI ,

i am sending the show version command output for your reference

------------------ show version ------------------

Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.2(4)M1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Thu 26-Jul-12 19:34 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)

RoyalEnfield uptime is 1 hour, 20 minutes

System returned to ROM by power-on

System image file is "usbflash0:c1900-universalk9-mz.SPA.152-4.M1.bin"

Last reload type: Normal Reload

Last reload reason: power-on

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco CISCO1905/K9 (revision 1.0) with 225280K/36864K bytes of memory.

Processor board ID FGL164825WS

2 Gigabit Ethernet interfaces

1 Serial(sync/async) interface

1 terminal line

DRAM configuration is 64 bits wide with parity disabled.

255K bytes of non-volatile configuration memory.

249840K bytes of USB Flash usbflash0 (Read/Write)

License Info:

License UDI:

-------------------------------------------------

Device#            PID                              SN

-------------------------------------------------

*0              CISCO1905/K9          FGL164825WS    

Technology Package License Information for Module:'c1900'

-----------------------------------------------------------------

Technology    Technology-package           Technology-package

              Current       Type           Next reboot 

------------------------------------------------------------------

ipbase        ipbasek9      Permanent      ipbasek9

security      None          None           None

data          None          None           None

Configuration register is 0x2102

InayathUlla Sharieff
Cisco Employee
Cisco Employee

ASAK Mohammed,

Please correct me if I am wrong, Are you enabling NAT + NBAR on this device? If yes then probably you are running out of memory. Hence the option would be to dislabe the NBAR with NAT.

you can do the following in global config mode.

       no ip nat service nbar

  This command doesn't enable NBAR by default when you enable NAT.

  Note: You have only 256M of memory on that device.

We have recorded bug for this issue: CSCua65133

Please let me know if you have any questions.

HTH

Rgards

Inayath

*Plz rate this post if its helpfull and mark the thread as answered if this resolved your query.

Review Cisco Networking for a $25 gift card