01-25-2019 11:09 AM - edited 03-08-2019 05:08 PM
Hi,
I am trying to upgrade IOS on Nexus 9148. I have not worked with Nexus switches before. from what I am reading its a whole different beast comparing to normal Switches that I have seen. any help, guide and heads up to help me do this upgrade is greatly appreciated.
Best Regards,
Masood
Solved! Go to Solution.
01-25-2019 02:33 PM
Depend on how your setup, is the Dual Switches with vPC or singe nexusm Switch.
Either case.
1. what is the current version
2. what is the version you looking to upgrade,
3. check the upgrade path
4. read the release notes
and follow standard upgrade proceedures as mentioned below guide
https://davidring.ie/2014/10/03/cisco-mds-upgrading-firmware/
01-25-2019 02:33 PM
Depend on how your setup, is the Dual Switches with vPC or singe nexusm Switch.
Either case.
1. what is the current version
2. what is the version you looking to upgrade,
3. check the upgrade path
4. read the release notes
and follow standard upgrade proceedures as mentioned below guide
https://davidring.ie/2014/10/03/cisco-mds-upgrading-firmware/
01-25-2019 02:56 PM
01-25-2019 04:01 PM - edited 01-25-2019 04:02 PM
Once we know the current version and the one you like to upgrade to.
Bare in mind, if you have only 1 Switch, you expect to have service interuption and you need to do this upgraed in maintenance window.
01-25-2019 04:03 PM
01-26-2019 03:23 PM
Hello again,
Managed to console and configure basics, Management ports and stuff. Device manager not working which I assume is because of Java.
and there are two Switches. - making it difficult for me as I have not done this before. a new beast for me.
here is show version:
Software
BIOS: version 1.0.19
loader: version N/A
kickstart: version 5.2(8b)
system: version 5.2(8b)
BIOS compile time: 02/01/10
kickstart image file is: bootflash:/m9100-s3ek9-kickstart-mz.5.2.8b.bin
kickstart compile time: 12/25/2020 12:00:00 [07/03/2013 10:16:59]
system image file is: bootflash:/m9100-s3ek9-mz.5.2.8b.bin
system compile time: 6/5/2013 15:00:00 [07/03/2013 10:48:15]
Hardware
cisco MDS 9148 FC (1 Slot) Chassis ("1/2/4/8 Gbps FC/Supervisor-3")
Motorola, e500v2 with 1036300 kB of memory.
Processor Board ID JAF1807AAAN
Device name: UTP-Nexsus9148
bootflash: 1000944 kB
Kernel uptime is 0 day(s), 1 hour(s), 52 minute(s), 37 second(s)
Last reset
Reason: Unknown
System version: 5.2(8b)
Service:
UTP-Nexsus9148(config)#
can I upgrade to latest (0ne version below latest based on Cisco) or I need to go through steps to upgrade to a higher version?
Any advise on the device manager? when I say go to Cisco, Cisco page give 404 Error.
Best Regards,
Masood
01-26-2019 05:53 PM
01-25-2019 04:02 PM
02-07-2019 02:46 PM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide