ANNOUNCEMENT - The community will be down for maintenace this Thursday August 13 from 12:00 AM PT to 02:00 AM PT. As a precaution save your work.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
184
Views
5
Helpful
4
Replies
Highlighted
VIP Advocate

netflow top-talker 4500x IOS 3.8.4.e

Dear All,

I am missing something but what is it? Not getting any idea. I am configuring Netflow 9 and I am not getting top-talker on the prtg. 

 

flow record frPrtg
description Prtg
match ipv4 tos
match ipv4 protocol
match ipv4 source address
match ipv4 destination address
match transport source-port
match transport destination-port
match interface input
collect transport tcp flags
collect counter bytes
collect counter packets
collect timestamp sys-uptime first
collect timestamp sys-uptime last

!

flow exporter fePrtg-1
description WAN-traffic--Prtg
destination x.x.x.x
source Vlanxx
transport udp 9993
template data timeout 1200
option interface-table timeout 3600
option exporter-stats timeout 60

!

flow monitor fmPrtg-1
description WAN-traffic-Prtg
exporter fePrtg-1
cache timeout active 60
record frPrtg
!

 

can you guide me if I am missing anything?

Regards,
Deepak Kumar,
Don't forget to vote and accept the solution If this comment will make help you!
2 ACCEPTED SOLUTIONS

Accepted Solutions
Highlighted
Hall of Fame Expert

Re: netflow top-talker 4500x IOS 3.8.4.e

Hi,

Have you added "ip flow monitor ....input and output to the interfaces?

Also, you may want to add these and test again:

 

collect counter bytes long
collect counter packets long
collect counter bytes rate

HTH

View solution in original post

Highlighted
VIP Advocate

Re: netflow top-talker 4500x IOS 3.8.4.e

Thanks for the reply. I really appreciate your support. 

 

It was an issue with the PRTG team and the sensor was not enabled properly.  Thanks again.

Regards,
Deepak Kumar,
Don't forget to vote and accept the solution If this comment will make help you!

View solution in original post

4 REPLIES 4
Highlighted
Hall of Fame Expert

Re: netflow top-talker 4500x IOS 3.8.4.e

Hi,

Have you added "ip flow monitor ....input and output to the interfaces?

Also, you may want to add these and test again:

 

collect counter bytes long
collect counter packets long
collect counter bytes rate

HTH

View solution in original post

Highlighted
VIP Mentor

Re: netflow top-talker 4500x IOS 3.8.4.e

 

flow exporter fePrtg-1
description WAN-traffic--Prtg
destination x.x.x.x
source Vlanxx
no transport udp 9993   < is this configured other side (or try port below to work)

transport udp 2055
export-protocol netflow-v9

 


interface te 1/1/1
ip flow monitor XXXXXXXXX input

 

BB
*** Rate All Helpful Responses ***
Highlighted
VIP Advocate

Re: netflow top-talker 4500x IOS 3.8.4.e

Thanks for the reply. I really appreciate your support. 

 

It was an issue with the PRTG team and the sensor was not enabled properly.  Thanks again.

Regards,
Deepak Kumar,
Don't forget to vote and accept the solution If this comment will make help you!

View solution in original post

Highlighted
Hall of Fame Expert

Re: netflow top-talker 4500x IOS 3.8.4.e

Thanks for the feedback!

Glad to know the issue has been resolved.

Reza

Content for Community-Ad