07-11-2012 09:29 PM - edited 03-07-2019 07:44 AM
Hi,
Yesterday I configured the 7010 Nexus switch. I created a VDC and allocated few ports and configured VLAN for testing. After enabling feature interface-vlan i was allowed to configured L3 interface for the vlan. I assigned ip address and connected few server to check the reachability but it says Destination Host Unreachable.
NX OS Ver : n7000-s1-dk9.5.2.4.bin
Configuration of the VDC below. Please let me know if i am missing some configuration
feature telnet
feature udld
feature interface-vlan
feature lacp
vrf context management
ip route 0.0.0.0/0 10.95.253.193
vlan configuration 704
vlan 1,704
interface Vlan704
no shutdown
ip address 10.84.254.193/26
interface Ethernet2/5
switchport
switchport mode access
switchport access vlan 704
no shutdown
interface Ethernet8/48
switchport
switchport mode access
switchport access vlan 704
no shutdown
switch-DLACC# sh ip int brief
IP Interface Status for VRF "default"(1)
Interface IP Address Interface Status
Vlan704 10.84.254.193 protocol-up/link-up/admin-up
switch-DLACC# sh ip route
IP Route Table for VRF "default"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
10.84.254.192/26, ubest/mbest: 1/0, attached
*via 10.84.254.193, Vlan704, [0/0], 09:30:07, direct
10.84.254.193/32, ubest/mbest: 1/0, attached
*via 10.84.254.193, Vlan704, [0/0], 09:30:07, local
switch-DLACC#
switch-DLACC# ping 10.84.254.202
PING 10.84.254.202 (10.84.254.202): 56 data bytes
36 bytes from 10.84.254.193: Destination Host Unreachable
Request 0 timed out
36 bytes from 10.84.254.193: Destination Host Unreachable
^C
--- 10.84.254.202 ping statistics ---
2 packets transmitted, 0 packets received, 100.00% packet loss switch-DLACC#ping 10.84.254.202
PING 10.84.254.202 (10.84.254.202): 56 data bytes
36 bytes from 10.84.254.193: Destination Host Unreachable
Request 0 timed out
36 bytes from 10.84.254.193: Destination Host Unreachable
^C
--- 10.84.254.202 ping statistics ---
2 packets transmitted, 0 packets received, 100.00% packet loss
switch-DLACC# sh module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok
2 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok
3 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok
4 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok
5 0 Supervisor module-1X N7K-SUP1 active *
6 0 Supervisor module-1X N7K-SUP1 ha-standby
7 8 10 Gbps Ethernet XL Module N7K-M108X2-12L ok
8 48 10/100/1000 Mbps Ethernet XL Module N7K-M148GT-11L ok
9 48 10/100/1000 Mbps Ethernet XL Module N7K-M148GT-11L ok
10 32 1/10 Gbps Ethernet Module N7K-F132XP-15 ok
07-12-2012 03:47 AM
Hi Uvaraj,
Can you provide a diagram of the topology so I can attempt to help? Are the servers directly attached to the Nexus or is there additional equipment in between them?
Thanks
Anthony
07-12-2012 03:52 AM
Hi Uvaraj
which ip connected to Ethernet8/48
Please add
sh int eth 8/48
sh ip arp
sh mac add inter eth 8/48
Regards,
Alex
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide