cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

274
Views
5
Helpful
3
Replies
Explorer

Orange light on SUP card

I have an orange light on my SUP card in slot 3 of my 4507. Is that just because it's in standby?

 

4507#sh env
no temperature alarms


Module Sensor Temperature Status
------+--------------------------+--------------------+------------
1 air inlet 24C (41C,56C,66C) ok
1 air outlet (front) 23C (43C,57C,67C) ok
1 air outlet (back) 24C (45C,59C,69C) ok
3 air inlet 27C (51C,65C,68C) ok
3 air outlet 30C (69C,83C,86C) ok
4 air inlet 33C (51C,65C,68C) ok
4 air outlet 40C (69C,83C,86C) ok
5 air inlet 23C (45C,60C,70C) ok
5 air outlet 35C (61C,76C,86C) ok
6 air inlet 23C (45C,60C,70C) ok
6 air outlet 38C (61C,76C,86C) ok

Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C45-4200ACV AC 4200W good good good
PS1-1 110V good
PS1-2 110V good
PS2 PWR-C45-4200ACV AC 4200W good good good
PS2-1 110V good
PS2-2 110V good

Power supplies needed by system : 1
Power supplies currently available : 2

Chassis Type : WS-C4507R-E

Power consumed by backplane : 40 Watts

Switch Bandwidth Utilization : 1%

Supervisor Led Color : Green

Module 1 Status Led Color : Green
Module 2 Status Led Color : Green PoE Led Color : Green
Module 3 Status Led Color : Orange
Module 4 Status Led Color : Green
Module 5 Status Led Color : Green PoE Led Color : Green
Module 6 Status Led Color : Green PoE Led Color : Green
Module 7 Status Led Color : Green PoE Led Color : Green

Fantray : Good

Power consumed by Fantray : 135 Watts

 

4507#sh module
Chassis Type : WS-C4507R-E

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 24 1000BaseX (SFP) WS-X4624-SFP-E
2 6 SFP, 10/100/1000BaseT (RJ45)V, Cisco/I WS-X4506-GB-T
3 Supervisor
4 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E
5 48 10/100/1000BaseT POE E Series WS-X4648-RJ45V-E
6 48 10/100/1000BaseT POE E Series WS-X4648-RJ45V-E
7 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V

M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 0021.1c7d.1c01 to 0021.1c7d.1c18 1.1 Ok
2 0021.5510.158c to 0021.5510.1591 1.4 Ok
3 Unknown Unknown Unknown Other
4 001b.2a68.ed06 to 001b.2a68.ed0b 1.2 12.2(44r)SG 12.2(50)SG8 Ok
5 0023.5e1c.ba10 to 0023.5e1c.ba3f 1.1 Ok
6 0024.14af.fe00 to 0024.14af.fe2f 1.1 Ok
7 0014.6a1b.ece0 to 0014.6a1b.ed0f 2.2 Ok

Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Standby Supervisor SSO Disabled
4 Active Supervisor SSO Active

3 REPLIES 3
Hall of Fame Community Legend

Re: Orange light on SUP card

No, it means the supervisor card in slot 3 has rebooted into ROMmon mode.
Console into this supervisor card and reboot. Post the entire boot-up process.
And make sure the supervisor card is booting IOS version 12.2(50)SG8.
Highlighted
Explorer

Re: Orange light on SUP card

Willdo. Thanks and I'll post the output.

Beginner

Re: Orange light on SUP card

We hal also the same problem.

Module 4 Status Led Color : Orange

 

In Our case the Module 4 was Standby Supervisor and was rebooted in ROMMON mode.

We have rebooted the module with the IOS stored in Slot0 direcly from consol.

 

rommon > boot slot0:cat4500e-entservicesk9-mz.122-44.SG.bin

CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards