cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

2318
Views
0
Helpful
4
Replies
Highlighted
Beginner

OSPFv3 on Switch

So trying to run OSPFv3 on a IOSL2 and a NX-OS switch, I receive a error stating "Protocol not in this image". So does CML not going to allow me to use this protocol or is there a "fix" I can do (Not using a router)?

 

Snippet output from config:

DLS2(config)#ip routing
DLS2(config)#ipv6 unicast-routing
DLS2(config)#router ospfv3 1
Protocol not in this image

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
VIP Advocate

Re: OSPFv3 on Switch

As I know, IOSvL2 is not supported
Regards,
Deepak Kumar,
Don't forget to vote and accept the solution If this comment will make help you!

View solution in original post

4 REPLIES 4
Highlighted
VIP Mentor

Re: OSPFv3 on Switch

Hello,

 

are you using the VIRL (or IOSv) images ? Post the output of 'sh ver' of both devices...

Highlighted
Beginner

Re: OSPFv3 on Switch

Not able to access the NX-OS right now, but here is the IOSvL2

***IOSvL2***

DLS2(config)#do sho ver
Cisco IOS Software, vios_l2 Software (vios_l2-ADVENTERPRISEK9-M), Version 15.2(CML_NIGHTLY_20190423)FLO_DSGS7, EARLY DEPLOYMENT DEVELOPMENT BUILD, synced to V152_6_0_81_E
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2019 by Cisco Systems, Inc.
Compiled Tue 23-Apr-19 04:48 by mmen


ROM: Bootstrap program is IOSv

D2 uptime is 51 minutes
System returned to ROM by reload
System image file is "flash0:/vios_l2-adventerprisek9-m"
Last reload reason: Unknown reason

 

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco IOSv () processor (revision 1.0) with 722281K/62464K bytes of memory.
Processor board ID 9MKG1WP49VI
2 Virtual Ethernet interfaces
4 Gigabit Ethernet interfaces
DRAM configuration is 72 bits wide with parity disabled.
256K bytes of non-volatile configuration memory.
2097152K bytes of ATA System CompactFlash 0 (Read/Write)
0K bytes of ATA CompactFlash 1 (Read/Write)
11217K bytes of ATA CompactFlash 2 (Read/Write)
0K bytes of ATA CompactFlash 3 (Read/Write)

Configuration register is 0x101

Highlighted
VIP Advocate

Re: OSPFv3 on Switch

As I know, IOSvL2 is not supported
Regards,
Deepak Kumar,
Don't forget to vote and accept the solution If this comment will make help you!

View solution in original post

Highlighted
Beginner

Re: OSPFv3 on Switch

Hmm, seems strange that the designers would program a option of using OSPFv3 but not actually provide the service for it. Just wasn’t sure if I was missing something special for the virtual lab equipment. So my fix action was to just replace the switch with a router and modify the requirements of the lab for the students. Thanks.

Content for Community-Ad