cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1203
Views
4
Helpful
14
Replies

Ping At L3 3560

dipak-parmar
Level 1
Level 1

Dear Sir,

I have layer3 3560 switch, switch Ip 192.168.1.1

I have One Pc with ip 192.168.1.10 & other Pc 192.168.1.11

Some times I can not get the ping of 192.168.1.11 from 192.168.1.10

At that time if ping its gateway means 192,168.1.1 , its gets reply , an then

Started reply from 192.168.1.11.

Why it was occur I can not understand. Help Me.

Thanking You

Dipak Parmar

14 Replies 14

smothuku
Level 7
Level 7

Have you configured default gateway on both pc's.

Thanks,

Satish

Does the pcs connected to same switch or different,

if in same switch check the port setting (speed& duplex).

have you seek with any other Pc like IP in the same subnet,

if pcs in different switch during the problem time try ping with different Pc, and check in the uplink port any errors.

they both are on same switch

i checked speed & Duplex

if i check ping for other pc i do not get

reply at that time

thanking you

Sir ,

ya configured that.

Hi Dipak ,

can you paste the config of the switch .....

Thanks,

Satish

guruprasadr
Level 7
Level 7

HI Dipak,

Can you please check the "Netmask" configured is same for Switch IP, PC1 & PC2.

Check the Default Gateway of the PC's.

See the Port Status to which PC1 & PC2 connected. Try to do some extended Ping from Switch.

Check whether the ports are in Forwarding / Blocking State.

Do multiple ping from different Src - to - destn.. & see the status of the Switch Int...

PLS Rate if Helps

Best Regards,

Guru Prasad R

sir,

subnet mask of switch ip Pc1,Pc2 is 255.255.255.0

both pc defalt gateway 192.168.1.1/24

port status up

Timor_SSS
Level 1
Level 1

Try to see logs (show loggin), see if there are any changes on port status when the problem accures.

Check you arp table on the switch, see if you're able to see both Pc's on arp on the same Vlan. Check you arp table on the Pc's as well. i suspect you have some sort of ARP issue on on of your servers or the switch.

If you'll post the running-config, it might help finding the problem more rapidly.

Regards,

Tim

Thanks TIMor,

I have same suspects ,

how I increase my arp cache , & rapid

Refresh rate to sort this arp issue

I am sending my configuration

at Switch

!

version 12.2

no service pad

service timestamps debug uptime

service timestamps log datetime localtime

no service password-encryption

!

ip subnet-zero

ip routing

no ip domain-lookup

!

!

!

!

no errdisable detect cause pagp-flap

no errdisable detect cause dtp-flap

no errdisable detect cause link-flap

no errdisable detect cause l2ptguard

no errdisable detect cause sfp-config-mismatch

no errdisable detect cause gbic-invalid

no errdisable detect cause dhcp-rate-limit

no errdisable detect cause arp-inspection

no errdisable detect cause loopback

no file verify auto

!

spanning-tree mode pvst

spanning-tree logging

spanning-tree extend system-id

no spanning-tree vlan 2,6

!

vlan internal allocation policy ascending

!

!

interface GigabitEthernet0/1

description "PC2"

switchport access vlan 6

switchport mode access

speed 1000

duplex full

!

interface GigabitEthernet0/2

description "PC1"

switchport access vlan 6

switchport mode access

speed 1000

duplex full

interface Vlan6

description "Third Floor LAN"

ip address 192.168.1.1 255.255.255.0

!

ip classless

Hi ,

set the speed and duplex on g0/1 and g0/2 of switch to "auto" and check the issue.

Thanks,

satish

ahmet-saat
Level 1
Level 1

Hi Dipak,

Are u using 3560 as Layer3 or Layer2. I mean if you have vlans, you can check that the PCs are on same VLAN.

Pls rate if it helps..

ya Dear they are on same VLAN

yes

mathew.webb
Level 1
Level 1

Try putting the switch ports into a portfast mode and see if you can ping.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: