01-22-2020 03:45 PM - edited 01-22-2020 03:52 PM
Dear all,
I have already verified the following output however actually is it normally impossible to collect with management port
on Cat4500-X?
##### Management Port #####
Cat4500-X(config)#int fa1
Cat4500-X(config-if)#ip flow monitor MONITOR input
% Flow Monitor: Flow Monitor 'MONITOR' : Flow Monitor not supported on interface FastEthernet1.
Cat4500-X(config-if)#ip flow monitor MONITOR layer2-switched input
% Flow Monitor: Flow Monitor 'MONITOR' : Flow Monitor not supported on interface FastEthernet1.
##### Data Port #####
Cat4500-X(config)#int te1/1
Cat4500-X(config-if)#ip flow monitor MONITOR input
The following is related URL which says Flow collection is supported on Port however it does not say Management Port that is why...
[Catalyst 4500 Series Switch Software Configuration Guide, Release IOS XE 3.3.0SG and IOS 15.1(1)SG]
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/15-1/XE_330SG/configuration/guide/config/fnf.html
Flow collection is supported on multiple targets (Port, VLAN, per-port per-VLAN
(FNF can be enabled on a specific VLAN on a given port)) and on a port-channel (FNF is configured on the port-channel interface,
rather than individual member ports).
##### Export from Management port - Export is possible! #####
Cat4500-X(config)#flow exporter EXPORT
Cat4500-X(config-flow-exporter)#destination 192.168.1.254 vrf mgmtVrf
Cat4500-X(config-flow-exporter)#source fastEthernet 1
Cat4500-X#sh flow exporter
Flow Exporter EXPORT:
Description: User defined
Export protocol: NetFlow Version 9
Transport Configuration:
Destination IP address: 192.168.1.254
VRF label: mgmtVrf
Source IP address: 192.168.1.1
Source Interface: FastEthernet1
Transport Protocol: UDP
Destination Port: 9995
Source Port: 60484
DSCP: 0x0
TTL: 255
Output Features: Not Used
Regards,
Masanobu Hiyoshi
01-22-2020 04:10 PM
Hi,
It appears that you need 03.08.00.E or later to get all the features you need. See link:
HTH
01-22-2020 04:36 PM
01-22-2020 05:11 PM
Glad to help!
It appears that you have both versions loaded on the flash. So, it is just a matter of changing the boot variable to 03.09.00.E.152-5.E.bin and reloading the switch.
HTH
01-22-2020 05:21 PM
Hi Reza,
Thank you for your support, unfortunately even if it is IOS-XE-Ver.3.9.0.E, the output looks same.
Cat4500-X#sh version
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.09.00.E RELEASE SOFTWARE (fc1)
*omit
Cat4500-X(config)#int fa1
Cat4500-X(config-if)#ip flow monitor MONITOR input
% Flow Monitor: Flow Monitor 'MONITOR' : Flow Monitor not supported on interface FastEthernet1.
Cat4500-X(config-if)#
Cat4500-X(config-if)#int te1/1
Cat4500-X(config-if)#ip flow monitor MONITOR input
01-22-2020 05:23 PM
I appreciate if you can let me know support URL like release note, configuration guide something like that :)!.
01-22-2020 07:16 PM
Hi,
There doesn't seem to be any document supporting this function on the out-of-band management port. So, you may want to use a regular port for this purpose.
HTH
01-22-2020 07:53 PM
Hi
That would be fine. Thank you very much!!.
Yes this info might be greatfully HTH (Hope This Helps).
Best Regards,
Masanobu Hiyoshi
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide