cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1096
Views
0
Helpful
2
Replies

QOS 6513 SUP2 AVAYA VOIP

Bradford.berry
Level 1
Level 1

Hello All,

I am in need of some asistance, I have searched for days one forums and Google and am unable to find a sample config that doesnt use autoqos.

I need to enable QOS on a 6513 that i am using as a access switch.( loaded with

WS-X6148-45AF).  I am running SUP2MFSC2 with IOS and autoqos is not supported. 

below is my IOS version and my requirements.

Requirements:

Trust CoS and DiffServ Value coming from Avaya equipments

DiffServ=46 for Audio and DiffServ=26 for Signaling

CoS=5 for Audio and CoS=3 for Signaling

I am running the following IOS:

IOS (tm) s222_rp Software (s222_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF17b, RELEASE SOFTWARE (fc1)

Sample Port config:( Vlan 709 = Data,Vlan 809=VOIP)

switchport

switchport access vlan 709

  switchport mode access

switchport voice vlan 809

no ip address

spanning-tree portfast

end

show mls qos

  QoS is enabled globally

  QoS ip packet dscp rewrite enabled globally

  Input mode for GRE Tunnel is Pipe mode

  Vlan or Portchannel(Multi-Earl) policies supported: Yes

  Egress policies supported: No

----- Module [2] -----

  QoS global counters:

    Total packets: 33034

    IP shortcut packets: 0

    Packets dropped by policing: 0

    IP packets with TOS changed by policing: 2349

    IP packets with COS changed by policing: 30

    Non-IP packets with COS changed by policing: 0

sho mls qos maps

   Normal Burst Policed-dscp map:                                  (dscp= d1d2)

     d1 :  d2 0  1  2  3  4  5  6  7  8  9

     -------------------------------------

      0 :    00 01 02 03 04 05 06 07 08 09

      1 :    10 11 12 13 14 15 16 17 18 19

      2 :    20 21 22 23 24 25 26 27 28 29

      3 :    30 31 32 33 34 35 36 37 38 39

      4 :    40 41 42 43 44 45 46 47 48 49

      5 :    50 51 52 53 54 55 56 57 58 59

      6 :    60 61 62 63

   Maximum Burst Policed-dscp map:                                  (dscp= d1d2)

     d1 :  d2 0  1  2  3  4  5  6  7  8  9

     -------------------------------------

      0 :    00 01 02 03 04 05 06 07 08 09

      1 :    10 11 12 13 14 15 16 17 18 19

      2 :    20 21 22 23 24 25 26 27 28 29

      3 :    30 31 32 33 34 35 36 37 38 39

      4 :    40 41 42 43 44 45 46 47 48 49

      5 :    50 51 52 53 54 55 56 57 58 59

      6 :    60 61 62 63

   Dscp-cos map:                                  (dscp= d1d2)

     d1 :  d2 0  1  2  3  4  5  6  7  8  9

     -------------------------------------

      0 :    00 00 00 00 00 00 00 00 01 01

      1 :    01 01 01 01 01 01 02 02 02 02

      2 :    02 02 02 02 03 03 03 03 03 03

      3 :    03 03 04 04 04 04 04 04 04 04

      4 :    05 05 05 05 05 05 05 05 06 06

      5 :    06 06 06 06 06 06 07 07 07 07

      6 :    07 07 07 07

   Cos-dscp map:

         cos:   0  1  2  3  4  5  6  7

     ------------------------------------

        dscp:   0  6 16 26 32 46 48 56

   IpPrecedence-dscp map:

      ipprec:   0  1  2  3  4  5  6  7

     ------------------------------------

        dscp:   0  8 16 24 32 40 48 56

Your help will be greatly appreciated.

Regards,

Brad

2 Replies 2

Fabienne Stephanoff
Cisco Employee
Cisco Employee

Hello Bradford,

I believe this type of card does support "mls qos trust dscp" under the interface config. Can you give that a try?

Fabienne

TAC

jkrysinski
Level 1
Level 1

Hi,

I was wondering if you found a solution?  I am in the same boat as you and can't find anything on the Avaya site besides the autoqos.

Thanks,

James

Review Cisco Networking for a $25 gift card