"show inventory" cannot display chassis-1 line card and module info in Cat6500 VSS mode

[Rps-Cheers]

HI Everyone,

Thesedays, we are occuring a issue that  is "show inv" command cannot display full info of two cat6500 device in VSS mode.

We have done some steps on VSS before,

First, we power down all cat6500 device(chassis1 is the active role,and chassis 2 is the secondary one).Then, we power on the chassis1, and power on chassis2 after it boot complete.Finally, we can see the VSS mode normal by "show switch virtual" command, it shown as below:

C6K-SW01#show switch virtual
Switch mode : Virtual Switch
Virtual switch domain number : 100
Local switch number : 1
Local switch operational role: Virtual Switch Active
Peer switch number : 2
Peer switch operational role : Virtual Switch Standby
Conversion completed : No
Perform exec command 'switch accept mode virtual' to complete the VSS conversion

There is the problem,we cannot get the full info by "show inv" in chassis1,we can only see some module on chassis2,but we cannot find any info about chassis1,just like this:

C6K-SW01#show inventory
NAME: "Chassis 2 WS-C6509-E", DESCR: "Chassis 2 Cisco Systems, Inc. Catalyst 6500 9-slot Chassis System"
PID: WS-C6509-E , VID: V05, SN: SMCXXXXXXXX

NAME: "Chassis 2 WS-C6K-VTT-E 1", DESCR: "Chassis 2 VTT-E FRU 1"
PID: WS-C6K-VTT-E , VID: , SN: SMTXXXXXXXX

NAME: "Chassis 2 WS-C6K-VTT-E 2", DESCR: "Chassis 2 VTT-E FRU 2"
PID: WS-C6K-VTT-E , VID: , SN: SMTXXXXXXXX

NAME: "Chassis 2 WS-C6K-VTT-E 3", DESCR: "Chassis 2 VTT-E FRU 3"
PID: WS-C6K-VTT-E , VID: , SN: SMTXXXXXXXX

NAME: "Chassis 2 CLK-7600 1", DESCR: "Chassis 2 OSR-7600 Clock FRU 1"
PID: CLK-7600 , VID: , SN: SMTXXXXXXXX

NAME: "Chassis 2 CLK-7600 2", DESCR: "Chassis 2 OSR-7600 Clock FRU 2"
PID: CLK-7600 , VID: , SN: SMTXXXXXXXX

NAME: "Chassis 2 1", DESCR: "Chassis 2 WS-X6704-10GE CEF720 4 port 10-Gigabit Ethernet Rev. 3.1"
PID: WS-X6704-10GE , VID: V03, SN: SALXXXXXXXX

NAME: "Chassis 2 WS-F6700-CFC Centralized Forwarding Card EARL sub-module of 1", DESCR: "Chassis 2 WS-F6700-CFC Centralized Forwarding Card Rev. 4.1"
PID: WS-F6700-CFC , VID: V06, SN: SALXXXXXXXX

NAME: "Chassis 2 Transceiver Te2/1/1", DESCR: "Chassis 2 Transceiver 10Gbase-LRM Te2/1/1"
PID: XENPAK-10GB-LRM , VID: V01 , SN: AGAXXXXXXXX

NAME: "Chassis 2 WS-C6509-E-FAN 1", DESCR: "Chassis 2 Enhanced 9-slot Fan Tray 1"
PID: WS-C6509-E-FAN , VID: V03, SN: DCHXXXXXXXX

NAME: "Chassis 2 PS 1 WS-CAC-3000W", DESCR: "Chassis 2 AC power supply, 3000 watt 1"
PID: WS-CAC-3000W , VID: V01, SN: AZSXXXXXXXX

NAME: "Chassis 2 PS 2 WS-CAC-3000W", DESCR: "Chassis 2 AC power supply, 3000 watt 2"
PID: WS-CAC-3000W , VID: V01, SN: AZSXXXXXXXX

Do you know what wrong with this ?

[balaji.bandi]

show inventory should show all, try another command as below

show module switch all

[Rps-Cheers]

Yes,I also think so it can be shown by "show inv"
I have test,it can be shown by "show module switch all" command ,but not "show inv" command.

thx

[balaji.bandi]

I am running code  Version 15.2(1)SY3

show inventory on Cat 6509-E with VSS shows both the switches.

[Rps-Cheers]

HI BB，

Yes, it can be shown before we reload two cat6509, i don't know if we need reload the device again...

[JunaidM]

Hi

Use "Show inventory raw" command in privilege mode, if it works,

Please rate helpful.

Thanks.