05-02-2012 04:59 AM - edited 03-07-2019 06:27 AM
Hello
Recently bought a module EHWIC 4ESG-in will install the cisco router 2921.
But the cisco router is not recognizing this module.
How to proceed?
sh inv
NAME: "CISCO2921/K9 chassis", DESCR: "CISCO2921/K9 chassis"
PID: CISCO2921/K9 , VID: V01 , SN: FTX1406AJZU
NAME: "4 Port FE Switch on Slot 0 SubSlot 0", DESCR: "4 Port FE Switch"
PID: HWIC-4ESW , VID: V01 , SN: FOC14200JG8
NAME: "C2921/C2951 AC Power Supply", DESCR: "C2921/C2951 AC Power Supply"
PID: PWR-2921-51-AC , VID: V01 , SN: QCS1349H0CU
show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1, REL EASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)
-
System returned to ROM by power-on
System image file is "flash0:c2900-universalk9-mz.SPA.150-1.M1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
Cisco CISCO2921/K9 (revision 1.0) with 483328K/40960K bytes of memory.
Processor board ID FTX1406AJZU
4 FastEthernet interfaces
3 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
254464K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*0 CISCO2921/K9 FTX1406AJZU
Technology Package License Information for Module:'c2900'
----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
-----------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc None None None
data None None None
Configuration register is 0x2102
Solved! Go to Solution.
05-02-2012 05:17 AM
http://www.cisco.com/en/US/prod/collateral/routers/ps10536/data_sheet_c78-612808.html
According to the spec sheet you need IOS 15.1(2)T or higher.
Hope this helps. -Ed
05-02-2012 05:17 AM
http://www.cisco.com/en/US/prod/collateral/routers/ps10536/data_sheet_c78-612808.html
According to the spec sheet you need IOS 15.1(2)T or higher.
Hope this helps. -Ed
05-02-2012 05:23 AM
Right.
When upgrading, the settings are lost?
thank you very much
12-21-2023 10:28 AM
Hi, I have 15.2 version installed and still do not see it. Any ideas?
05-02-2012 05:31 AM
Your configuration should not be affected. However, safety and sanity always dictate that you back up your configuration before making such a change. Also, although unlikely config syntax can change slightly between versions. Check the release files and be ready to revert just in case.
Just to make sure this is understood, upgrading the IOS will need to be performed during a scheduled outrage if this is on a production network.
-Ed
05-29-2012 07:56 AM
Hi,
After extensive research it was discovered that the gigabit module is not compatible with the module fast ethernet was already installed.
In a new arrest, and possible removal of this module has been recognized by the IOS, the new module.
No more, thanks for all help.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide