01-26-2019 02:50 PM - edited 03-08-2019 05:09 PM
hello all,
i have c3850 that needs to be connected to 1G circuit.
Currently on c3850, nm-4-10g is installed. i'm using SFP, glc-lh-sm, ("1000BaseLX SFP") for the port.
Is that SFP compatible with network module that I have? or does NM-4-10g only supports 10g?
Currently it's plugged into te1/1/4
NAME: "Te1/1/4", DESCR: "1000BaseLX SFP"
Switch is recognizing SFP that i'm using and grabbing SN off of SFP as well.
I did no shut command to keep a port alive.
Is SFP compatible with network module? or does it require speed configuration?
when i plug in the fiber, no link is coming up, not even an amber light. it's a dead port.
Please help.
Solved! Go to Solution.
01-28-2019 01:44 PM
I had to speed nonegotiate
01-26-2019 02:59 PM - edited 01-26-2019 02:59 PM
C3850-NM-4-10G (four 10-Gigabit slots or four 1-Gigabit slots)
Refer below document :
01-26-2019 04:04 PM
is there any config do i need to apply? or it should work when i plug in?
01-27-2019 01:33 AM
What is other side switch and sfp information. can you post show version and port-configuration to have look.
if possible default the interace config and config again and check, if the port unshut mode on multi mode you can see one side red laser glowing. ( do not look directly from your eyes, it is not recomended,)
if other side is ok, then you see same laser light on the fibre patch lead.
01-28-2019 06:33 AM
it's coming from the cross connect.
Switch#sho ver
Cisco IOS Software [Denali], Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 16.3.6, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Wed 28-Feb-18 15:23 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2018 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.58, RELEASE SOFTWARE (P)
interface TenGigabitEthernet1/1/1
!
interface TenGigabitEthernet1/1/2
!
interface TenGigabitEthernet1/1/3
!
interface TenGigabitEthernet1/1/4
01-26-2019 04:00 PM
@leej48 wrote:
Switch is recognizing SFP that i'm using and grabbing SN off of SFP as well.
I did no shut command to keep a port alive.
What firmware is the switch running on?
01-28-2019 06:29 AM
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.58, RELEASE SOFTWAR E (P)
01-28-2019 01:44 PM
I had to speed nonegotiate
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide