cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
11656
Views
15
Helpful
25
Replies
Highlighted
Rising star

I know this is kinda obvious,

I know this is kinda obvious, but did you copy/paste the filename in on the command line or did you type it by hand?  I recommend copy paste.  I only ask because I've been burned by that myself before.

Highlighted
Beginner

copy paste. I noted the

copy paste.

 

I noted the following in the SecureCRT settings. Upload was set to diffent area than .bin file islocated. will try again

sMc
Highlighted
Beginner

no success I issued the

no success

 

I issued the format flash

flash_init

reset.

 

here is what i have now. Does this make any sense?

 


switch: format flash:
Are you sure you want to format "flash:" (all data will be lost) (y/n)?y
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 32513024
flashfs[0]: flashfs fsck took 7 seconds.
Setting console baud rate to 9600...
Filesystem "flash:" formatted

switch: ?
           ? -- Present list of available commands
        boot -- Load and boot an executable image
         cat -- Concatenate (type) file(s)
        copy -- Copy a file
      delete -- Delete file(s)
         dir -- List files in directories
  flash_init -- Initialize flash filesystem(s)
      format -- Format a filesystem
        fsck -- Check filesystem consistency
        help -- Present list of available commands
 load_helper -- Load and initialize a helper image
      memory -- Present memory heap utilization information
       mkdir -- Create dir(s)
        more -- Concatenate (display) file(s)
      rename -- Rename a file
       reset -- Reset the system
       rmdir -- Delete empty dir(s)
         set -- Set or display environment variables
      set_bs -- Set attributes on a boot sector filesystem
   set_param -- Set system parameters in flash
       sleep -- Pause (sleep) for a specified number of seconds
 -- MORE --
        trap -- Cause a software breakpoint to occur
        type -- Concatenate (type) file(s)
       unset -- Unset one or more environment variables
     version -- Display boot loader version

switch: dir

List of filesystems currently registered:

               flash[0]: (read-write)
              xmodem[1]: (read-only)
                null[2]: (read-write)
                  bs[3]: (read-only)


switch: flash_init
Initializing Flash...
...The flash is already initialized.
Setting console baud rate to 9600...

switch: reset
Are you sure you want to reset the system (y/n)?y
System resetting...

Base ethernet MAC Address: 00:19:e7:72:7e:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 32513024
flashfs[0]: flashfs fsck took 7 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
done.
Loading "flash:/c3750-ipservicesk9-mz.122-55.SE9.bin"...flash:/c3750-ipservicesk9-mz.122-55.SE9.bin: no such file or directory

Error loading "flash:/c3750-ipservicesk9-mz.122-55.SE9.bin"

Interrupt within 5 seconds to abort boot process.
Boot process failed...

The system is unable to boot automatically.  The BOOT
environment variable needs to be set to a bootable
image.


switch:

sMc
Highlighted
Rising star

It makes sense. It's looking

It makes sense. It's looking for an image in flash that matches the boot string. Since you just wiped flash, it will fail because there is no image. You can try the xmodem transfer again. 

Highlighted
Rising star

Also, did you delete the old

Also, did you delete the old IOS image?  Just the little things that could break the process have to be checked.

Highlighted
Beginner

So far no matter what BAUD

So far no matter what BAUD rate I set (9600 or 115200), I get same results!?

sMc
Highlighted
Rising star

Baud rate is just for the

Baud rate is just for the purposes of transfer speed in this situation.  Most folks go with 115200 because it's quite a bit faster than 9600 as far as bitrate/transfer speed.  Results will be the same, just that the 9600 rate takes significantly longer.

Highlighted
Beginner

Re: Run your command, using

Thanks Antonio, The "3rd C" statement really helped :)

Highlighted
Beginner

Still getting same response

Still getting same response

 

switch: copy  xmodem: flash:c3750-ipservicesk9-mz.122-55.SE9.bin
Begin the Xmodem or Xmodem-1K transfer now...
CCCCCCCCCCxmodem:: I/O error

 

What am I missing??

sMc
Highlighted
Beginner

Re: switch: CCCCCCCCCCxmodem:: I/O error

I'ved the same problem, but i solved with this :  on my cisco 34xx baud 115200 and on my terminal too 115200.

switch: copy -b 115200 xmodem: flash:me340x-metroipaccessk9-mz.122-60.EZ11.bin
Begin the Xmodem or Xmodem-1K transfer now...
C............................................................................... ..........................................................
File "xmodem:" successfully copied to "flash:me340x-metroipaccessk9-mz.122-60.EZ 11.bin"

switch: dir flash:
Directory of flash:/

2 -rwx 15690496 <date> me340x-metroipaccessk9-mz.122-60.EZ1 1.bin

12179456 bytes available (15818752 bytes used)

Highlighted
Beginner

Re: switch: CCCCCCCCCCxmodem:: I/O error

change the console .

 

CreatePlease to create content
Content for Community-Ad