switch not boot

[Ramprasad2]

hi team,

i have Cisco 9200L its not boot properly its showing below logs

Initializing Hardware...
Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
act2_read_raw_idprom failed...
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
System Bootstrap, Version 17.9.1r [FC8], RELEASE SOFTWARE (P)
Compiled Sat 07/23/2022 16:14:02 by rel

Current ROMMON image : Primary
platform with 2097152 Kbytes of main memory

Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
TAM Init Failed
Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
TAM Init Failed
boot: attempting to boot from [cat9k_lite_iosxe.17.03.06.SPA.bin]
Please wait while the system restarts.

Initializing Hardware...
Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
act2_read_raw_idprom failed...
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
System Bootstrap, Version 17.9.1r [FC8], RELEASE SOFTWARE (P)
Compiled Sat 07/23/2022 16:14:02 by rel

Current ROMMON image : Primary
platform with 2097152 Kbytes of main memory

Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
TAM Init Failed
Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
TAM Init Failed
boot: attempting to boot from [cat9k_lite_iosxe.17.03.06.SPA.bin]
Please wait while the system restarts.

Initializing Hardware...
Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
act2_read_raw_idprom failed...
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
System Bootstrap, Version 17.9.1r [FC8], RELEASE SOFTWARE (P)
Compiled Sat 07/23/2022 16:14:02 by rel

Current ROMMON image : Primary
platform with 2097152 Kbytes of main memory

Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
TAM Init Failed
Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
TAM Init Failed
boot: attempting to boot from [cat9k_lite_iosxe.17.03.06.SPA.bin]
Please wait while the system restarts.

Initializing Hardware...
Bus is busy - 0x2(status)
ERROR: TAM write failed (3000)
ERROR: TAM write failed (3000)
act2_read_raw_idprom failed...
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
Unable to read byte 1. Timing Out !
System Bootstrap, Version 17.9.1r [FC8], RELEASE SOFTWARE (P)
Compiled Sat 07/23/2022 16:14:02 by rel

Current ROMMON image : Primary
platform with 2097152 Kbytes of main memory

[Reza Sharifi]

Hi,

Open a ticket with TAC. You may need to RMA it if it is a hardware issue.

HTH

[Leo Laohoo]

Call Cisco TAC and organize an RMA for the switch is dead.  

[randolph_harris]

I'm getting the same on one of my 9200L's. A work around until you can get it replaced is to unplug the power cord, wait for a few seconds and then plug the power cord back in and hold down the mode button until you see

boot: failed to load flash:/user/packages.conf (Aborted)

ERROR: failed to boot from flash:packages.conf (Aborted)

at the switch: prompt type reset and the y 

it should boot normally from that point

[randolph_harris]

After doing the workaround above. I downgraded the IOS from cat9k_lite_iosxe.17.03.06.SPA.bin to cat9k_lite_iosxe.17.03.05.SPA.bin which cleared out the issue

[Tran Quang VInh]

How do it this when the device no boot complete?

[peaceg92]

Hi

i did same

i typed reset but it doesn’t go past

initializing hardware…

system bootstrap, version 17.9.1r [FC8],Release software P

current ROMMON image:primary 

C9200-24T platform with 4194304kbytes of memory 

TAM init failed

TAM init failed

boot:attempting to boot from[flash:packages.conf]

[randolph_harris]

Instead of typing the reset command do a physical pull of the power cord

[randolph_harris]

As soon as you apply power, press the mode button. It should take you to the location where you can do it.