cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3394
Views
0
Helpful
9
Replies

terminate the WAN link on a switch.

manjit_raulo
Level 1
Level 1

Regarding the Ethernet ports,that also available on routers .....so is there any specific criteria for choosing the WAN link type & specific bandwidth when we want to terminate the WAN link on a switch.

And also....if we want to terminate the link on a layer 3 switch...is there any extra equipment or converter required ??

1 Accepted Solution

Accepted Solutions

Manjit

Yes you can do this but you would then need to configure shaping on the port on the 3750 so you do not exceed the 2Mb bandwidth - use the config guide as a starting point for shaping -

http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_46_se/configuration/guide/swqos.html

Jon

View solution in original post

9 Replies 9

Jon Marshall
Hall of Fame
Hall of Fame

Manjit

"so is there any specific criteria for choosing the WAN link type & specific bandwidth when we want to terminate the WAN link on a switch."

Not sure i follow. As long as the link is ethernet you choose the bandwidth.

"f we want to terminate the link on a layer 3 switch...is there any extra equipment or converter required ??"

Again, it needs to be presented as ethernet and you will be fine. Obviously if they present fibre you need a fibre connection on your switch. If the WAN termination is anything other than ethernet you would need some sort of intermediate device such as a router.

Jon

thanks Jon....

Is it possible to terminate a 2MB Ethernet WAN link on a fastethernet port of cisco 3750 switch.

Manjit

Yes you can do this but you would then need to configure shaping on the port on the 3750 so you do not exceed the 2Mb bandwidth - use the config guide as a starting point for shaping -

http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_46_se/configuration/guide/swqos.html

Jon

Thanks Jon....

As I don't have much idea on applying qos & till now ...I never configured any qos yet.

So have to study on this particular topic.

Is there any particular link to start qos from the very basic level.

That would be very helpful.

thanks again.

Hi,

Can anyone please tell me the differnce between terminating a link on a cisco 3750X versuse an ISR G2 router?

Also, can i terminate a link of 124mbps on a switch?

Appreciate your qucik response.

Disclaimer

The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.

Liability Disclaimer

In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.

Posting

What kind of link?  124 Mbps?

If you're thinking just Ethernet, assuming your ports supports the actual physical type of Ethernet, either should be able to terminate the link.

Joseph W. Doherty
Hall of Fame
Hall of Fame

Disclaimer

The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.

Liability Disclaimer

In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.

Posting

Often when dealing with WAN links with Ethernet hand-offs, they can be terminated on any devices that provides the matching physical Ethernet type.  However, as WAN links, even with Ethernet hand-offs often have less than typical LAN Ethernet (logical) bandwidths (your 2 Mbps being a case in point), LAN oriented switches often don't have the features to manage the bandwidth similarly to most routers.  For example, on a router, you might have:

interface FastEthernet 0/0

traffic-shape rate 2000000

Which shapes your rate to your 2 Mbps and WFQs traffic (a fairly effective, but simple, QoS).

Most (small) LAN switches would not offer a shaper nor FQ feature.

BTW, there's MetroEthernet switches offer enhanced features, compared to a LAN switch, but for up to about 10 Mbps, I would recommend an ISR.

Hi,

The link is a normal Ethernet 124 mbps link terminating on a 3750X 48 ports switch.

This link will only be used for Replicating data from DC to DR.

Will it now be ok to terminate on 3750X 48 port switch?

Disclaimer

The   Author of this posting offers the information contained within this   posting without consideration and with the reader's understanding that   there's no implied or expressed suitability or fitness for any purpose.   Information provided is for informational purposes only and should not   be construed as rendering professional advice of any kind. Usage of  this  posting's information is solely at reader's own risk.

Liability Disclaimer

In   no event shall Author be liable for any damages whatsoever (including,   without limitation, damages for loss of use, data or profit) arising  out  of the use or inability to use the posting's information even if  Author  has been advised of the possibility of such damage.

Posting

What's "normal" with 124 Mbps Ethernet?  I only know of Ethernet, FastEthernet, GigEthernet and 10 GigEthernet, but 124 Mbps Ethernet?  Might this be GigEthernet rate-limited to 124 Mbps?

If you're only going to send one kind of bulk data, such as replication data, then yes a 3750-X would be okay, although a router supporting RED or FRED might obtain a higher goodput rate but not enough I would worry about it.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: