cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2804
Views
14
Helpful
10
Replies

Trunk And EtherChannel

Not applicable

Trunk and EtherChannel were united between Catalyst6509(CatOS) and

Catalyst2950.

EthetChannel was not able to be united ahead normally when turning on

power after it blacked out.

The composition and LOG are the following.

Are not there any hints?

---Physical connection---

CAT2950-FA0/23 <-> CAT6509-3/27

CAT2950-FA0/24 <-> CAT6509-4/27

---Config---

Cat6509 + Sup2

clear trunk 3/27 3-6,8-1001,1025-4094

set trunk 3/27 desirable dot1q 1-2,7,1002-1005

set port channel 3/27 mode desirable silent

clear trunk 4/27 3-6,8-1001,1025-4094

set trunk 4/27 desirable dot1q 1-2,7,1002-1005

set port channel 4/27 mode desirable silent

Cat2950

!

interface FastEthernet0/23

switchport trunk allowed vlan 1,2,7,1002-1005

switchport mode trunk

channel-group 1 mode desirable

!

interface FastEthernet0/24

switchport trunk allowed vlan 1,2,7,1002-1005

switchport mode trunk

channel-group 1 mode desirable

!

---LOG---

Cat2950

%EC-5-DONTBNDL: Fa0/24 suspended: incompatible partner port with FastEthernet0/23

%EC-5-DONTBNDL: Fa0/24 suspended: incompatible partner port with FastEthernet0/23

Cat6509

%DTP-5-NONTRUNKPORTON:Port 4/27 has become non-trunk

%DTP-5-TRUNKPORTON:Port 4/27 has become dot1q trunk

%DTP-5-NONTRUNKPORTON:Port 4/27 has become non-trunk

%DTP-5-TRUNKPORTON:Port 4/27 has become dot1q trunk

---PORT STATUS---

Cat6509

4/27 connected trunk a-full a-100 10/100BaseTX

Cat2950

Fa0/24 notconnect trunk a-full a-100 10/100BaseTX

1 Accepted Solution

Accepted Solutions

I believe Edison is correct , on the catos side when you do the ports individually it will put them in different port channel groups and won't be able to agregate them which is indicated by your debug . Group them together and they should build the channel and trunk just fine . We haven't had any problems autonegotiating trunks or etherchannels on catos boxes.

View solution in original post

10 Replies 10

Edison Ortiz
Hall of Fame
Hall of Fame

On the CatOS side type:

set port channel 3/27,4/27

On the 2950 side type:

interface range f0/23-24

shut

no shut

HTH,

__

Edison.

thank you.

The setting has already been done.

Besides, though there might be a cause ・・・

set port channel 3/27,4/27 28

s.arunkumar
Level 3
Level 3

Hi

I think u are missing with cmd for trunking method to be used at 2950.

Use the cmd "switchport trunk encapsulation dot1q" on ports fa0/23 and fa0/24..

Also i dont thing the Pgap need to configure on silent mode.Silent mode is used when the other end is not capable of Pgap.

arun

Arun,

2950 does not support ISL hence the only option is 802.1q

When there is only one option, the encapsulation command is not available.

I believe the problem is with the CatOS not having 3/27 and 4/27 as channel partners. The command I recommended should fix the issue.

__

Edison.

Thanks edison for correcting me... :)

arun

Not applicable

I tried the below.

ï½¥The Trunk mode is changed from Dynamic to turning on and it connects it. (2950 was

connected with LAN cable between 6509 again. )

ï½¥Restart of 2950

Debug was made effective by 2950 and the information gathering was

done.

debug dtp event

debug pagp event

debug dtp packet

The result is appended LOG.

Is anything understood?

I am doubting that PAGP is doubtful.

1) Can you change the trunk on the 6509 from desirable to on ?

2) Can you change the channel-group on the 2950 from desirable to auto ?

Do step 1 first, if it doesn't work then do step 2.

__

Edison.

Thank you for advice.

I will try on weekend.

It reports on the result again.

I believe Edison is correct , on the catos side when you do the ports individually it will put them in different port channel groups and won't be able to agregate them which is indicated by your debug . Group them together and they should build the channel and trunk just fine . We haven't had any problems autonegotiating trunks or etherchannels on catos boxes.

Not applicable

The setting change was done getting a hint from advice.

When the channel setting of 6509 and 2950 was made ON Mode, it became

normal.

Thank you.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco