cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
18255
Views
0
Helpful
3
Replies

Upgrade a license from LAN Base to IP Base on a WS-C3750X-48P-L stack

vladakoci
Level 1
Level 1

Hello,

I do have two WS-C3750X-48P-L switches with LAN Base license stacked. I want to upgrade the license on each from LAN Base to IP Base.

Got .lic files from Cisco partner and stored them in flash:

shan2021#dir flash:
Directory of flash:/

  442  -rwx       13260   Apr 1 2011 13:48:20 +02:00  config.text
  443  -rwx        1936   Mar 1 1993 02:53:30 +01:00  vlan.dat
  444  -rwx        1152   Mar 1 1993 03:01:55 +01:00  FD01503Z1C5_20110330204317053.lic
  445  -rwx        1152   Mar 1 1993 03:08:14 +01:00  FD01503R0WU_20110330204634394.lic
  447  -rwx        1909   Apr 1 2011 13:48:20 +02:00  private-config.text
    2  drwx         512   Mar 1 1993 01:16:57 +01:00  c3750e-universalk9-mz.122-53.SE2
  448  -rwx        3096   Apr 1 2011 13:48:20 +02:00  multiple-fs

57671680 bytes total (40040448 bytes free)
shan2021#

Tried to upgrade with the commands

shan2021#license install flash:FD01503Z1C5_20110330204317053.lic
Installing licenses from "flash:FD01503Z1C5_20110330204317053.lic"
% Error: Install failed. UDI WS-C3750X-48P-L:FD01503Z1C5 on license does not match any device
0/1 licenses were successfully installed
0/1 licenses were existing licenses
1/1 licenses were failed to install

shan2021#

shan2021#license install flash:FD01503R0WU_20110330204634394.lic
Installing licenses from "flash:FD01503R0WU_20110330204634394.lic"
% Error: Install failed. UDI WS-C3750X-48P-L:FD01503R0WU on license does not match any device
0/1 licenses were successfully installed
0/1 licenses were existing licenses
1/1 licenses were failed to install

shan2021#

But this does not work. The UDIs seem to be correct:

shan2021#sho license udi
Device#   PID                   SN              UDI
-----------------------------------------------------------------------------
*1        WS-C3750X-48P-L       FDO1503Z1C5     WS-C3750X-48P-L:FDO1503Z1C5
2        WS-C3750X-48P-L       FDO1503R0WU     WS-C3750X-48P-L:FDO1503R0WU

shan2021#

Guessed that maybe because they are stacked the process does not work, so was rebooting the second one and tried to upgrade the license on the first one during seond's reboot, but it did not work either.

I do not have a physicall access to the switches, so cannot try to remove stack cables.

Does anyone know, is there a special command to upgrade the license in case the LAN Base 3750X switches are stacked?

I know the upgrade on a standalone switch works fine, I tried on some other one.

I believe the .lic files are okay, looked into them and they do not seem to be wrong.

Here is the full sho ver

shan2021#sho ver
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(53)SE2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 21-Apr-10 05:11 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02400000

ROM: Bootstrap program is C3750E boot loader
BOOTLDR: C3750E Boot Loader (C3750X-HBOOT-M) Version 12.2(53r)SE1, RELEASE SOFTWARE (fc1)

shan2021 uptime is 3 hours, 53 minutes
System returned to ROM by power-on
System restarted at 10:51:37 CEST Fri Apr 1 2011
System image file is "flash:/c3750e-universalk9-mz.122-53.SE2/c3750e-universalk9-mz.122-53.SE2.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
export@cisco.com. Level: lanbase
License Type: Permanent
Next reload license Level: lanbase

If

License

cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1503Z1C5
Last reset from power-on
2 Virtual Ethernet interfaces
1 FastEthernet interface
104 Gigabit Ethernet interfaces
4 Ten Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address       : C8:9C:1D:5C:7C:00
Motherboard assembly number     : 73-12553-04
Motherboard serial number       : FDO15040UGP
Model revision number           : A0
Motherboard revision number     : A0
Model number                    : WS-C3750X-48P-L
Daughterboard assembly number   : 800-32727-01
Daughterboard serial number     : FDO15040SQM
System serial number            : FDO1503Z1C5
Top Assembly Part Number        : 800-31324-01
Top Assembly Revision Number    : A0
Version ID                      : V01
CLEI Code Number                : COMJZ00ARA
Hardware Board Revision Number  : 0x02


Switch Ports Model              SW Version            SW Image
------ ----- -----              ----------            ----------
*    1 54    WS-C3750X-48P      12.2(53)SE2           C3750E-UNIVERSALK9-M
     2 54    WS-C3750X-48P      12.2(53)SE2           C3750E-UNIVERSALK9-M


Switch 02
---------
Switch Uptime                   : 1 hour, 1 minute
Base ethernet MAC Address       : C8:9C:1D:3C:39:80
Motherboard assembly number     : 73-12553-04
Motherboard serial number       : FDO15032371
Model revision number           : A0
Motherboard revision number     : A0
Model number                    : WS-C3750X-48P-L
Daughterboard assembly number   : 800-32727-01
Daughterboard serial number     : FDO1503153L
System serial number            : FDO1503R0WU
Top assembly part number        : 800-31324-01
Top assembly revision number    : A0
Version ID                      : V01
CLEI Code Number                : COMJZ00ARA
License Level                   : lanbase
License Type                    : Permanent
Next reboot licensing Level     : lanbase


Configuration register is 0xF

shan2021#

shan2021#sho license all
License Store: Primary License Storage
StoreIndex: 0   Feature: lanbase                           Version: 1.0
        License Type: Permanent
        License State: Active, In Use
        License Priority: Medium
        License Count: Non-Counted

License Store: Evaluation License Storage
StoreIndex: 0   Feature: ipservices                        Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8  weeks 4  days
            Evaluation period left: 8  weeks 4  days
        License Priority: None
        License Count: Non-Counted


shan2021#

Need IP Base to add non-3750X switches and also because of Stack Power.

Guess maybe there is a specific command license add for a stack, something like

license install flash:FD01503Z1C5_20110330204317053.lic switch 1
but have not found any such.

Many thanks for help,

Vlad


1 Accepted Solution

Accepted Solutions

Reza Sharifi
Hall of Fame
Hall of Fame

Hi Vlad,

Make sure that the exact UID of each device including lower case and upper case letters are used to generate the license key, if not it will not work.

You can also generate the keys yourself by going to this link and loogin with your CCO account

https://tools.cisco.com/SWIFT/Licensing/RegistrationServlet

HTH

Reza

View solution in original post

3 Replies 3

Reza Sharifi
Hall of Fame
Hall of Fame

Hi Vlad,

Make sure that the exact UID of each device including lower case and upper case letters are used to generate the license key, if not it will not work.

You can also generate the keys yourself by going to this link and loogin with your CCO account

https://tools.cisco.com/SWIFT/Licensing/RegistrationServlet

HTH

Reza

Hello Reza,

many thanks for the advice. It was a Cisco partner that did it for us. The UID seem to be correct, please, see my text above.

Actually they provided three .lic files. One I apllied on a standalone switch ( not stacked ) and the process worked well. The two remaining are stacked and on these the process does not work. It's just my guess but maybe there is a bug in license utility and it does not work correctly if the switches are stacked.

Thanks anyway,

Vlad

We can now see that our Cisco partner has made a mistake while generating license files.

They should use WS-C3750X-48P-L:FDO1503Z1C5   instead of WS-C3750X-48P-L:FD01503Z1C5, in other words the letter O was replaced with the digit 0.

Review Cisco Networking products for a $25 gift card