user getting disconnect for ever 12 hours in lan network

syed baseeruddin · ‎12-14-2018

link getting Down & UP for every 12 0r 24 hour

we have to core switch one old network and onther new network

so we make trunk between old and new network

old network trunk configuration

interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 8,12
switchport mode trunk
spanning-tree guard root

new network trunk configuration

interface TenGigabitEthernet1/1/13
description *** Connected to SW-3560-A ***
switchport trunk allowed vlan 8,12
switchport mode trunk
end

for spanning for old network for vlan 8 & 12
VLAN0008
Spanning tree enabled protocol ieee
Root ID Priority 24584
Address 0026.0b06.ff80
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

Bridge ID Priority 24584 (priority 24576 sys-id-ext 8)
Address 0026.0b06.ff80
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300 sec

Interface Role Sts Cost Prio.Nbr Type
------------------- ---- --- --------- -------- --------------------------------
Gi0/1 Desg FWD 4 128.1 P2p
Gi0/2 Desg FWD 4 128.2 P2p
Fa0/12 Desg FWD 19 128.14 P2p
Fa0/21 Desg FWD 19 128.23 P2p Edge

VLAN0012
Spanning tree enabled protocol ieee
Root ID Priority 32768
Address 24d9.2126.0001
Cost 27
Port 2 (GigabitEthernet0/2)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

Bridge ID Priority 32780 (priority 32768 sys-id-ext 12)
Address 0026.0b06.ff80
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300 sec

Interface Role Sts Cost Prio.Nbr Type
------------------- ---- --- --------- -------- --------------------------------
Gi0/1 Desg FWD 4 128.1 P2p
Gi0/2 Root FWD 4 128.2 P2p
Fa0/12 Desg FWD 19 128.14 P2p

for network spanning tree for vlan 8 & 12

VLAN0008
Spanning tree enabled protocol rstp
Root ID Priority 24584
Address 0026.0b06.ff80
Cost 4
Port 13 (TenGigabitEthernet1/1/13)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

Bridge ID Priority 32776 (priority 32768 sys-id-ext 8)
Address 0008.e3ff.fd90
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300 sec

Interface Role Sts Cost Prio.Nbr Type
------------------- ---- --- --------- -------- --------------------------------
Te1/1/13 Root FWD 4 128.13 P2p Peer(STP)
Po1 Desg FWD 3 128.2561 P2p Peer(STP)
Po2 Desg FWD 3 128.2562 P2p Peer(STP)
Po3 Desg FWD 3 128.2563 P2p Peer(STP)
Po4 Desg FWD 3 128.2564 P2p Peer(STP)
Po5 Desg FWD 3 128.2565 P2p Peer(STP)
Po250 Desg FWD 3 128.2810 P2p Peer(STP)

VLAN0012
Spanning tree enabled protocol rstp
Root ID Priority 32768
Address 24d9.2126.0001
Cost 31
Port 13 (TenGigabitEthernet1/1/13)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

Bridge ID Priority 32780 (priority 32768 sys-id-ext 12)
Address 0008.e3ff.fd90
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300 sec

Interface Role Sts Cost Prio.Nbr Type
------------------- ---- --- --------- -------- --------------------------------
Te1/1/13 Root FWD 4 128.13 P2p Peer(STP)
Po1 Desg FWD 3 128.2561 P2p Peer(STP)
Po2 Desg FWD 3 128.2562 P2p Peer(STP)
Po3 Desg FWD 3 128.2563 P2p Peer(STP)
Po4 Desg FWD 3 128.2564 P2p Peer(STP)
Po5 Desg FWD 3 128.2565 P2p Peer(STP)
Po250 Desg FWD 3 128.2810 P2p Peer(STP)

Georg Pauwen · ‎12-15-2018

Hello,

what do the logs show as the reason for the interfaces, or the links, going down ?

syed baseeruddin · ‎12-15-2018

Hello

Thanks

old networks logs switch log

SW-3560-A#sh log
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.

No Inactive Message Discriminator.

    Console logging: level debugging, 145 messages logged, xml disabled,
                     filtering disabled
    Monitor logging: level debugging, 0 messages logged, xml disabled,
                     filtering disabled
    Buffer logging: level debugging, 145 messages logged, xml disabled,
                     filtering disabled
    Exception Logging: size (4096 bytes)
    Count and timestamp logging messages: disabled
    File logging: disabled
    Persistent logging: disabled

No active filter modules.

Trap logging: level informational, 149 message lines logged

Log Buffer (4096 bytes):
e to down
4w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to down
4w2d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to down
4w3d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to up
4w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to up
4w6d: %LINK-3-UPDOWN: Interface FastEthernet0/13, changed state to up
4w6d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
4w6d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
4w6d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
4w6d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
4w6d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
5w0d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to down
5w0d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to down
5w0d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to up
5w0d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to up
5w0d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to down
5w0d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to down
5w0d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to up
5w0d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to up
5w5d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
5w5d: %LINK-3-UPDOWN: Interface FastEthernet0/13, changed state to down
6w1d: %LINK-3-UPDOWN: Interface FastEthernet0/13, changed state to up
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to down
6w1d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to down
6w1d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to up
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to up
6w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
6w1d: %LINK-3-UPDOWN: Interface FastEthernet0/13, changed state to down
6w4d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to down
6w4d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to down
6w4d: %LINK-3-UPDOWN: Interface FastEthernet0/21, changed state to up
6w4d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/21, changed state to up
7w1d: %LINK-3-UPDOWN: Interface FastEthernet0/13, changed state to up
7w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
7w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
7w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
7w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
7w1d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to up
7w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to down
7w2d: %LINK-3-UPDOWN: Interface FastEthernet0/13, changed state to down
7w3d: %SPANTREE-2-ROOTGUARD_CONFIG_CHANGE: Root guard disabled on port GigabitEthernet0/1.
7w3d: %SYS-5-CONFIG_I: Configured from console by maradmin on vty0 (10.200.14.109)
7w3d: %SPANTREE-2-ROOTGUARD_CONFIG_CHANGE: Root guard enabled on port GigabitEthernet0/1.
7w3d: %SYS-5-CONFIG_I: Configured from console by maradmin on vty0 (10.200.14.109)
SW-3560-A#sh clo
SW-3560-A#sh clock
*20:17:44.939 UTC Thu Apr 22 1993

interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 8,12
switchport mode trunk
spanning-tree guard root

==========================================================

New Network

interface TenGigabitEthernet1/1/13
description *** Connected to SW-3560-A ***
switchport trunk allowed vlan 8,12
switchport mode trunk
end

NEW-ADMIN-CORE#sh log
Syslog logging: enabled (0 messages dropped, 4 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.

No Inactive Message Discriminator.

    Console logging: level debugging, 67 messages logged, xml disabled,
                     filtering disabled
    Monitor logging: level debugging, 0 messages logged, xml disabled,
                     filtering disabled
    Buffer logging: level debugging, 67 messages logged, xml disabled,
                    filtering disabled
    Exception Logging: size (8192 bytes)
    Count and timestamp logging messages: disabled
    Persistent logging: disabled

No active filter modules.

Trap logging: level informational, 68 message lines logged
Logging Source-Interface: VRF Name:

Log Buffer (32768 bytes):

*Oct 4 06:58:52.421: %BUFCAP-6-EPC_RF_INFRA: EPC rf infra registration is SUCCESS
*Oct 4 06:58:58.168: %C4K_IOSSYS-6-IMAGELEVEL: Supervisor booting in image level 'ipbase'
*Oct 4 07:00:14.727: %C4K_IOSINTF-5-LMPHWSESSIONSTATE: Lmp HW session UP on slot 1 port 15.
*Oct 4 07:00:14.754: %C4K_IOSINTF-5-LMPHWSESSIONSTATE: Lmp HW session UP on slot 1 port 16.
*Oct 4 07:00:30.729: %VSLP-5-VSL_UP: Ready for control traffic

*Oct 4 07:00:33.735: %VSLP-5-RRP_ROLE_RESOLVED: Role resolved as ACTIVE by VSLP
*Oct 4 07:01:03.793: %C4K_REDUNDANCY-6-INIT: Initializing as ACTIVE supervisor
*Oct 4 07:01:05.375: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Oct 4 07:01:07.282: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 1 (WS-C4500X-16 S/N: JAE212600NM Hw: 1.1) is online
*Oct 4 07:01:08.358: %C4K_REDUNDANCY-6-DUPLEX_MODE: The peer Supervisor has been detected
*Oct 4 07:01:11.938: %SPANTREE-6-PORTDEL_ALL_VLANS: Port-channel102 deleted from all Vlans
*Oct 4 07:01:12.008: %SPANTREE-6-PORTDEL_ALL_VLANS: Port-channel201 deleted from all Vlans
*Oct 4 07:01:12.525: %SW_VLAN-6-VTP_DOMAIN_NAME_CHG: VTP domain name changed to MRH-ADMIN-NW.
*Oct 4 07:01:12.575: %SYS-5-CONFIG_I: Configured from memory by consoleSystem has been configured

*Oct 4 07:01:12.740: %SYS-5-RESTART: System restarted --
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.09.00.E RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Tue 19-Jul-16 15:19 by prod_rel_team
*Oct 4 07:01:13.293: %EC-5-BUNDLE: Interface TenGigabitEthernet1/1/15 joined port-channel Port-channel102
*Oct 4 07:01:13.336: %EC-5-BUNDLE: Interface TenGigabitEthernet1/1/16 joined port-channel Port-channel102
*Oct 4 07:01:17.144: %EC-5-BUNDLE: Interface Te1/1/14 joined port-channel Po250
*Oct 4 07:01:19.154: %SPANTREE-7-RECV_1Q_NON_TRUNK: Received 802.1Q BPDU on non trunk Port-channel250 VLAN1.
*Oct 4 07:01:19.154: %SPANTREE-7-BLOCK_PORT_TYPE: Blocking Port-channel250 on VLAN0001. Inconsistent port type.
*Oct 4 07:01:19.802: %EC-5-BUNDLE: Interface Te1/1/2 joined port-channel Po2
*Oct 4 07:01:19.975: %EC-5-BUNDLE: Interface Te1/1/5 joined port-channel Po5
*Oct 4 07:01:20.049: %EC-5-BUNDLE: Interface Te1/1/1 joined port-channel Po1
*Oct 4 07:01:20.065: %EC-5-BUNDLE: Interface Te1/1/4 joined port-channel Po4
*Oct 4 07:01:20.145: %EC-5-BUNDLE: Interface Te1/1/3 joined port-channel Po3
*Oct 4 07:01:30.825: %C4K_IOSMODPORTMAN-6-MODULEONLINE: Module 11 (WS-C4500X-16 S/N: JAE212600L6 Hw: 1.1) is online
*Oct 4 07:01:30.851: %C4K_REDUNDANCY-6-MODE: ACTIVE supervisor initializing for sso mode
*Oct 4 07:01:31.083: %C4K_REDUNDANCY-3-COMMUNICATION: Communication with the peer Supervisor has been established
*Oct 4 07:01:31.128: %BUFCAP-6-SERVER_INIT: EPC SPI server init SUCCESSFUL
*Oct 4 07:01:31.128: %BUFCAP-6-CLIENT: EPC SPI client is BORN
*Oct 4 07:01:41.459: %EC-5-UNBUNDLE: Interface Te1/1/14 left the port-channel Po250
*Oct 4 07:01:41.504: %C4K_REDUNDANCY-5-CONFIGSYNC: The config-reg has been successfully synchronized to the standby supervisor
*Oct 4 07:01:41.506: %C4K_REDUNDANCY-5-CALENDAR: The calendar has been successfully synchronized to the standby supervisor for the first time
*Oct 4 07:01:41.506: %C4K_REDUNDANCY-5-CONFIGSYNC: The startup-config has been successfully synchronized to the standby supervisor
*Oct 4 07:01:41.956: %C4K_REDUNDANCY-5-CONFIGSYNC: The private-config has been successfully synchronized to the standby supervisor
*Oct 4 07:01:42.816: %C4K_REDUNDANCY-5-CONFIGSYNC_RATELIMIT: The vlan database has been successfully synchronized to the standby supervisor
*Oct 4 07:01:48.169: %EC-5-BUNDLE: Interface Te1/1/14 joined port-channel Po250
*Oct 4 07:01:51.283: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=1: Transceiver has been inserted
*Oct 4 07:01:51.283: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=2: Transceiver has been inserted
*Oct 4 07:01:51.283: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=3: Transceiver has been inserted
*Oct 4 07:01:51.284: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=4: Transceiver has been inserted
*Oct 4 07:01:51.284: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=5: Transceiver has been inserted
*Oct 4 07:01:51.284: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=9: Transceiver has been inserted
*Oct 4 07:01:51.285: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=14: Transceiver has been inserted
*Oct 4 07:01:51.285: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=15: Transceiver has been inserted
*Oct 4 07:01:51.285: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=11 Port=16: Transceiver has been inserted
*Oct 4 07:02:16.283: %EC-5-BUNDLE: Interface TenGigabitEthernet2/1/15 joined port-channel Port-channel201
*Oct 4 07:02:16.301: %EC-5-BUNDLE: Interface TenGigabitEthernet2/1/16 joined port-channel Port-channel201
*Oct 4 07:02:21.081: %HA_CONFIG_SYNC-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succeeded
*Oct 4 07:02:22.061: %RF-5-RF_TERMINAL_STATE: 1 ha_mgr: Terminal state reached for (SSO)
*Oct 4 07:02:20.995: %C4K_IOSMODPORTMAN-6-MODULEONLINE: STANDBY:Module 1 (WS-C4500X-16 S/N: JAE212600NM Hw: 1.1) is online
*Oct 4 07:02:20.995: %C4K_IOSMODPORTMAN-6-MODULEONLINE: STANDBY:Module 11 (WS-C4500X-16 S/N: JAE212600L6 Hw: 1.1) is online
*Oct 4 07:02:28.289: %EC-5-CANNOT_BUNDLE2: Te2/1/14 is not compatible with Te1/1/14 and will be suspended (trunk mode of Te2/1/14 is access, Te1/1/14 is trunk)
*Oct 4 07:02:28.245: %EC-5-CANNOT_BUNDLE2: STANDBY:Te2/1/14 is not compatible with Te1/1/14 and will be suspended (trunk mode of Te2/1/14 is access, Te1/1/14 is trunk)
*Oct 4 07:02:32.799: %EC-5-BUNDLE: Interface Te2/1/3 joined port-channel Po3
*Oct 4 07:02:32.989: %EC-5-BUNDLE: Interface Te2/1/1 joined port-channel Po1
*Oct 4 07:02:32.993: %EC-5-BUNDLE: Interface Te2/1/2 joined port-channel Po2
*Oct 4 07:02:33.089: %EC-5-BUNDLE: Interface Te2/1/4 joined port-channel Po4
*Oct 4 07:02:33.263: %EC-5-BUNDLE: Interface Te2/1/5 joined port-channel Po5
*Oct 4 07:02:33.075: %EC-5-BUNDLE: STANDBY:Interface Te2/1/4 joined port-channel Po4
*Oct 4 07:02:33.248: %EC-5-BUNDLE: STANDBY:Interface Te2/1/5 joined port-channel Po5
*Oct 4 07:02:34.628: %EC-5-BUNDLE: STANDBY:Interface Te2/1/1 joined port-channel Po1
*Oct 4 07:02:35.484: %EC-5-BUNDLE: STANDBY:Interface Te2/1/2 joined port-channel Po2
*Oct 4 07:02:36.073: %EC-5-BUNDLE: Interface Te2/1/14 joined port-channel Po250
*Oct 4 07:02:36.032: %EC-5-BUNDLE: STANDBY:Interface Te2/1/14 joined port-channel Po250
*Oct 4 07:02:37.015: %EC-5-BUNDLE: STANDBY:Interface Te2/1/3 joined port-channel Po3
NEW-ADMIN-CORE#

Georg Pauwen · ‎12-15-2018

Hello,

what does your topology look like ? The 4500 is a much bigger switch (as opposed to the 3560) and should ideally be the root.

Either way, if you need to keep the 3560 as the root, try and manually set the root priority for your VLANs on the 3560:

spanning-tree vlan 8 priority 1

spanning-tree vlan 12 priority 1