08-09-2012 06:22 AM - edited 03-07-2019 08:15 AM
Good afternoon,
I have an other niggling question, My switch Vlan looks all clear but when i run the command show running-config, to check that all IP information has been erased from the switch the Vlan is showing an IP address and i need help removing this, see content rom switch below.
switch#
switch#en
switch#show ru
Building configuration...
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname switch
!
!
!
!
!
!
!
ip subnet-zero
!
!
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface VLAN1
ip address 192.6.8.1 255.255.255.0
no ip directed-broadcast
no ip route-cache
!
!
line con 0
transport input none
stopbits 1
line vty 0 4
login
line vty 5 15
login
!
end
switch#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4,
Fa0/5, Fa0/6, Fa0/7, Fa0/8,
Fa0/9, Fa0/10, Fa0/11, Fa0/12,
Fa0/13, Fa0/14, Fa0/15, Fa0/16,
Fa0/17, Fa0/18, Fa0/19, Fa0/20,
Fa0/21, Fa0/22, Fa0/23, Fa0/24,
Gi0/1, Gi0/2
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active
1005 trnet-default active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
1002 fddi 101002 1500 - 0 - - - 0 0
1003 tr 101003 1500 - 0 - - srb 0 0
1004 fdnet 101004 1500 - - - ieee - 0 0
1005 trnet 101005 1500 - - - ibm - 0 0
switch#
Regards
Paul
Solved! Go to Solution.
08-09-2012 07:49 AM
just login in switch...
switch#config t
Switch(Config)#int vlan 1
SWitch(Config-vlan)#no ip address
thats all you need to remove the ip.
Regards
Sandeep
08-09-2012 06:30 AM
Hi Paul.
use this
Switch#config t
Switch(Config-vlan)#Interface vlan x
Switch(Config-vlan)#no ip address
Regards
Please rate if it helps.
08-09-2012 07:27 AM
HI Sandeep
How do i access
Switch(Config-vlan) from privlage mode???
Paul
08-09-2012 07:49 AM
just login in switch...
switch#config t
Switch(Config)#int vlan 1
SWitch(Config-vlan)#no ip address
thats all you need to remove the ip.
Regards
Sandeep
08-09-2012 08:12 AM
Hi Paul,
you should probably to erase the file on the flash memory with all the info about the vlan. Often is vlan.dat
default interface vlan 1
could be something else to try.
Alessio
08-09-2012 11:58 PM
Sandeep,
Thank you for your support, the commands worked and i no longer have the Interface VLAN1 showing any IP address.
regards,
Paul
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: