Hallo All ,
I am not not able to ping from vrf to external networks , anyone could guide me.
vrf definition lan
!
address-family ipv4
exit-address-family
!
vrf definition prov-pri
!
address-family ipv4
exit-address-family
!
vrf definition prov-sec
!
address-family ipv4
exit-address-family
!
!
!
interface FastEthernet0/0
vrf forwarding prov-pri
ip address 13.13.13.1 255.255.255.0
duplex full
!
interface FastEthernet1/0
vrf forwarding prov-sec
ip address 12.12.12.1 255.255.255.0
duplex full
!
interface FastEthernet2/0
vrf forwarding lan
no ip address
speed auto
duplex auto
!
interface FastEthernet2/0.100
encapsulation dot1Q 100
vrf forwarding lan
ip address 192.168.100.1 255.255.255.0
!
interface FastEthernet2/0.200
encapsulation dot1Q 200
vrf forwarding lan
ip address 192.168.200.1 255.255.255.0
R1# show ip vrf
Name Default RD Interfaces
lan <not set> Fa2/0
Fa2/0.100
Fa2/0.200
prov-pri <not set> Fa0/0
prov-sec <not set> Fa1/0
R1#show ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 13.13.13.1 YES manual up up
FastEthernet1/0 12.12.12.1 YES manual up up
FastEthernet2/0 unassigned YES unset up up
FastEthernet2/0.100 192.168.100.1 YES manual up up
FastEthernet2/0.200 192.168.200.1 YES manual up up
FastEthernet2/1 unassigned YES unset administratively down down
R1#show run | sec ip rotue
R1#show run | sec ip route
ip route vrf lan 0.0.0.0 0.0.0.0 FastEthernet0/0 13.13.13.3
ip route vrf lan 0.0.0.0 0.0.0.0 FastEthernet1/0 12.12.12.2 20
ip route vrf lan 13.13.13.1 255.255.255.255 FastEthernet0/0 13.13.13.3
ip route vrf prov-pri 0.0.0.0 0.0.0.0 13.13.13.3
ip route vrf prov-sec 0.0.0.0 0.0.0.0 12.12.12.2
R1#show run | sec ip router
R1#show run | sec router
router eigrp 100
network 192.168.100.0
network 192.168.200.0
R1#
R1#ping vrf prov-pri 13.13.13.3 source fast
R1#ping vrf prov-pri 13.13.13.3 source fastEthernet 2/0.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 13.13.13.3, timeout is 2 seconds:
Packet sent with a source address of 192.168.100.1
.....
Success rate is 0 percent (0/5)
R1#ping vrf prov-pri 13.13.13.3 source fastEthernet 2/0.200
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 13.13.13.3, timeout is 2 seconds:
Packet sent with a source address of 192.168.200.1
.....
Success rate is 0 percent (0/5)
R1#ping vrf lan 192.168.100.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.100.254, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/7/32 ms
R1#ping vrf lan 192.168.200.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.200.254, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/15/40 ms
R1#ping vrf prov-pri 4.4.4.4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/64/120 ms
R1#ping vrf prov-sec 4.4.4.4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/52/68 ms
R1#
R1#ping vrf prov-pri 13.13.13.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 13.13.13.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/27/36 ms
R1#ping vrf prov-pri 13.13.13.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 13.13.13.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
R1#ping vrf prov-sec 12.12.12.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 12.12.12.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
R1#ping vrf prov-sec 12.12.12.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 12.12.12.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/21/36 ms
R1#ping vrf lan 13.13.13.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 13.13.13.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#ping vrf lan 13.13.13.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 13.13.13.3, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#ping vrf prov-sec 4.4.4.4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 40/80/136 ms
R1#ping vrf prov-pri 4.4.4.4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 4.4.4.4, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 36/71/96 ms
R1#
With Regards
