03-05-2019 06:59 AM
Good Day,
I have migrated two of my core switches. new cores are 9407 whereas, the access switches are a mixture of 2960 and 3850. All trunks are up and working but VTP version number is not getting matched. Since cores are the servers and access switches are the clients.
I have defaulted the interfaces on both sides one by one but the issue is not getting eliminated. Any suggestion as per experience, please?
Thanks for the support.
Regards,
03-05-2019 07:11 AM
03-05-2019 07:31 AM - edited 03-05-2019 07:32 AM
Can you post below information :
Show vtp Status and show vtp statistics (both server and client switches)
Also see sh vlan brief ( anything suspended) ? post the same output here
03-06-2019 01:26 AM
Good Day,
I shifted the mode to transparent from server/client....
VTP Version capable : 1 to 3
VTP version running : 1
VTP Domain Name : RHH
VTP Pruning Mode : Disabled
VTP Traps Generation : Enabled
Device ID : d4c9.3c6e.8dc0
Configuration last modified by 10.1.5.2 at 3-5-19 12:17:33
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 34
Configuration Revision : 0
MD5 digest : 0x64 0xA6 0xE4 0x3D 0x6D 0x08 0x18 0x8A
0x29 0xE0 0x38 0xA8 0xCD 0xCF 0x08 0x1C
*** MD5 digest checksum mismatch on trunk: Po12 ***
VTP Version capable : 1 to 3
VTP version running : 1
VTP Domain Name : RHH
VTP Pruning Mode : Disabled
VTP Traps Generation : Enabled
Device ID : d4c9.3c2a.6b00
Configuration last modified by 10.1.5.3 at 3-5-19 12:17:33
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 34
Configuration Revision : 0
MD5 digest : 0x1F 0xC0 0x2C 0x05 0xD5 0x69 0x67 0x69
0xFD 0x53 0x7D 0xA3 0x44 0x9E 0x6E 0xAA
*** MD5 digest checksum mismatch on trunk: Po12 ***
Sw1 (Source)
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : hospital
VTP Pruning Mode : Enabled
VTP Traps Generation : Enabled
Device ID : 78da.6ee7.9200
Configuration last modified by 10.1.5.13 at 11-14-16 10:57:31
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 38
Configuration Revision : 0
MD5 digest : 0xA4 0xE9 0x65 0xA6 0xD7 0xF0 0x9F 0x0D
0xFF 0x47 0xC8 0x07 0x2A 0xBB 0xBC 0x40
SW2 (Destination)
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : hospital
VTP Pruning Mode : Enabled
VTP Traps Generation : Enabled
Device ID : 6073.5c91.ac80
Configuration last modified by 10.1.5.10 at 11-14-16 10:57:31
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 38
Configuration Revision : 0
MD5 digest : 0xB4 0xD7 0x16 0x7E 0x96 0x5E 0xA7 0x43
0xD1 0x20 0xE5 0xAA 0x36 0x5E 0x64 0x73
I created one test vlan on all 4 switches....vl 100 from cores to SW1 and SW2 they can ping each other ..but SW1 and SW2 SVIs (vl100) are not pinging to each other.....
please advice...
03-06-2019 05:08 AM - edited 03-06-2019 12:33 PM
Hello
FYI - VTP version 1 and VTP version 2 are not applicable to work with each other on switches in the same VTP domain.
Looks like from your post all the switches support vtp 2 so suggest to make them all vtp ver 2 in the same domain and test again
03-06-2019 06:28 AM
below clear giving you the logs to take action, so change vtp version to 2 and if you looking to be client, make it from transparent to vtp client to fix the issue. and advise.
VTP Version capable : 1 to 3
VTP version running : 1
VTP Domain Name : RHH
VTP Pruning Mode : Disabled
VTP Traps Generation : Enabled
Device ID : d4c9.3c6e.8dc0
Configuration last modified by 10.1.5.2 at 3-5-19 12:17:33
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 34
Configuration Revision : 0
MD5 digest : 0x64 0xA6 0xE4 0x3D 0x6D 0x08 0x18 0x8A
0x29 0xE0 0x38 0xA8 0xCD 0xCF 0x08 0x1C
*** MD5 digest checksum mismatch on trunk: Po12 ***
VTP Version capable : 1 to 3
VTP version running : 1
VTP Domain Name : RHH
VTP Pruning Mode : Disabled
VTP Traps Generation : Enabled
Device ID : d4c9.3c2a.6b00
Configuration last modified by 10.1.5.3 at 3-5-19 12:17:33
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 34
Configuration Revision : 0
MD5 digest : 0x1F 0xC0 0x2C 0x05 0xD5 0x69 0x67 0x69
0xFD 0x53 0x7D 0xA3 0x44 0x9E 0x6E 0xAA
*** MD5 digest checksum mismatch on trunk: Po12 ***
03-06-2019 06:40 AM
VTP Version capable : 1 to 3
VTP version running : 1 < change from 1 to 2
VTP Domain Name : RHH
VTP Pruning Mode : Disabled
VTP Traps Generation : Enabled
Device ID : d4c9.3c6e.8dc0
Configuration last modified by 10.1.5.2 at 3-5-19 12:17:33
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 34
Configuration Revision : 0
MD5 digest : 0x64 0xA6 0xE4 0x3D 0x6D 0x08 0x18 0x8A
0x29 0xE0 0x38 0xA8 0xCD 0xCF 0x08 0x1C
*** MD5 digest checksum mismatch on trunk: Po12 *** << remove authentication or set the same for all switches
VTP Version capable : 1 to 3
VTP version running : 1 < change from 1 to 2
VTP Domain Name : RHH
VTP Pruning Mode : Disabled
VTP Traps Generation : Enabled
Device ID : d4c9.3c2a.6b00
Configuration last modified by 10.1.5.3 at 3-5-19 12:17:33
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 34
Configuration Revision : 0
MD5 digest : 0x1F 0xC0 0x2C 0x05 0xD5 0x69 0x67 0x69
0xFD 0x53 0x7D 0xA3 0x44 0x9E 0x6E 0xAA
*** MD5 digest checksum mismatch on trunk: Po12 *** << remove authentication or set the same for all switches
Sw1 (Source)
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : hospital < this domain is different from other first two domains.
VTP Pruning Mode : Enabled
VTP Traps Generation : Enabled
Device ID : 78da.6ee7.9200
Configuration last modified by 10.1.5.13 at 11-14-16 10:57:31
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 38
Configuration Revision : 0
MD5 digest : 0xA4 0xE9 0x65 0xA6 0xD7 0xF0 0x9F 0x0D
0xFF 0x47 0xC8 0x07 0x2A 0xBB 0xBC 0x40
SW2 (Destination)
VTP Version capable : 1 to 3
VTP version running : 2
VTP Domain Name : hospital < this domain is different from other first three domains.
VTP Pruning Mode : Enabled
VTP Traps Generation : Enabled
Device ID : 6073.5c91.ac80
Configuration last modified by 10.1.5.10 at 11-14-16 10:57:31
Feature VLAN:
--------------
VTP Operating Mode : Transparent
Maximum VLANs supported locally : 1005
Number of existing VLANs : 38
Configuration Revision : 0
MD5 digest : 0xB4 0xD7 0x16 0x7E 0x96 0x5E 0xA7 0x43
0xD1 0x20 0xE5 0xAA 0x36 0x5E 0x64 0x73
I created one test vlan on all 4 switches....vl 100 from cores to SW1 and SW2 they can ping each other ..but SW1 and SW2 SVIs (vl100) are not pinging to each other.....
Thanks in advance.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide