I have a Cisco 1841 router that I obtained for my CCNA home lab. I was going through the process of resetting the device to factory default and this message keeps appearing in a loop.
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
00046C 0X00016804 Virtual Private Network (VPN) Module
0X00020000 Crypto module pools
0X0052 0X0001A800 Card in slot 0
0X0052 0X0001A800 Card in slot 1
0X000021B8 Onboard USB
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Allocating additional 12898526 bytes to IO Memory.
PMem allocated: 245366784 bytes; IOMem allocated: 23068672 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 1841 Software (C1841-ADVENTERPRISEK9-M), Version 15.1(4)M7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Sun 15-Sep-13 23:44 by prod_rel_team
%ERR-1-GT64120 (PCI-0): Fatal error, Parity error on master read
GT=0x24000000, cause=0x0110E083, mask=0x0ED01F00, real_cause=0x00100000
--------------------------------------------------------------------
Possible hardware fault. This could be an one time occurence,
upon reoccurence please collect crashinfo, "show tech"
and contact Cisco Technical Support.
----------------------------------------------------------------------
bus_err_high=0x00000000, bus_err_low=0x00000000, addr_decode_err=0x00000470
r0 = FFFFFFFF r1 = FFFFFFFF r2 = 0 r3 = 65950000 r4 = FFFFFFFF
r5 = A3111400 r6 = FFFFFFFF r7 = BFC00000 r8 = 0 r9 = 0
r10 = 0 r11 = 0 r12 = 0 r13 = 680080 r14 = 0
r15 = 680080 r16 = 0 r17 = C100 r18 = 0 r19 = 0
r20 = 0 r21 = 0 r22 = 0 r23 = 80 r24 = 0
r25 = 680000 r26 = 0 r27 = D r28 = 0 r29 = 0
r30 = 0 r31 = D r32 = FFFFFFFF r33 = FFFFFFFF r34 = FFFFFFFF
r35 = FFFFFFFF r36 = FFFFFFFF r37 = FFFFFFFF r38 = FFFFFFFF r39 = FFFFFFFF
r40 = FFFFFFFF r41 = FFFFFFFF r42 = FFFFFFFF r43 = FFFFFFFF r44 = FFFFFFFF
r45 = FFFFFFFF r46 = FFFFFFFF r47 = FFFFFFFF r48 = 0 r49 = 0
r50 = 0 r51 = 0 r52 = 0 r53 = 3041E801 r54 = 0
r55 = 100000 r56 = FFFFFFFF r57 = FFFFFFFF r58 = 0 r59 = 6646AF38
r60 = FFFFFFFF r61 = FFFFFFFF r62 = 0 r63 = 6007905C
sreg = 3401C103 mdlo_hi = 0 mdlo = 7A12
mdhi_hi = 0 mdhi = 0 badvaddr_hi = FFFFFFFF
badvaddr = FFFFFFFF cause = FFFFFFFF epc_hi = 0
epc = 6007906C err_epc_hi = FFFFFFFF err_epc = FFFFFFFF
%ERR-1-FATAL: Fatal error interrupt, reloading
err_stat=0x0
=== Flushing messages (00:01:56 UTC Thu Jan 1 1970) ===
Queued messages:
*Mar 1 00:00:04.287: %ENVMON-4-RTC: The Real Time Clock may have battery problem or it has not been set to the current time
*Jan 1 00:01:47.427: SERVICE_MODULE(Serial0/0/0): self test finished: Passed
*Jan 1 00:01:50.195: SERVICE_MODULE(Serial0/1/0): self test finished: Passed
*Jan 1 00:01:56.395: %ENVMON-4-RTC: The Real Time Clock may have battery problem or it has not been set to the current time
00:01:57 UTC Thu Jan 1 1970: Interrupt exception, CPU signal 22, PC = 0x0
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback=
$0 : 00000000 00000000, AT : 00000000 00000000, v0 : 00000000 00000000, v1 : 00000000 00000000
a0 : 00000000 00000000, a1 : 00000000 00000000, a2 : 00000000 00000000, a3 : 00000000 00000000
t0 : 00000000 00000000, t1 : 00000000 00000000, t2 : 00000000 00000000, t3 : 00000000 00000000
t4 : 00000000 00000000, t5 : 00000000 00000000, t6 : 00000000 00000000, t7 : 00000000 00000000
s0 : 00000000 00000000, s1 : 00000000 00000000, s2 : 00000000 00000000, s3 : 00000000 00000000
s4 : 00000000 00000000, s5 : 00000000 00000000, s6 : 00000000 00000000, s7 : 00000000 00000000
t8 : 00000000 00000000, t9 : 00000000 00000000, k0 : 00000000 00000000, k1 : 00000000 00000000
gp : 00000000 00000000, sp : 00000000 00000000, s8 : 00000000 00000000, ra : 00000000 00000000
EPC : 00000000, ErrorEPC : 00000000, SREG : 00000000
MDLO : 00000000, MDHI : 00000000, BadVaddr : 00000000
TEXT_START : 0x60015AB0
DATA_START : 0x63C861E0
Cause 00000000 (Code 0x0): Interrupt exception
SYSTEM INIT: INSUFFICIENT MEMORY TO BOOT THE IMAGE!
%Software-forced reload
00:02:00 UTC Thu Jan 1 1970: Breakpoint exception, CPU signal 23, PC = 0x607C1FCC
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0x607BBDECz 0x607BA2F4z 0x62C964E0z 0x603FA65Cz 0x603EED14z 0x603EF10Cz 0x603EF1B0z 0x603F8F34z 0x60401E18z 0x617A5DBCz 0x617A6110z 0x6179FE84z 0x6179C4B4z 0x61198CC4z 0x61197420z 0x61197924z
$0 : 00000000 00000000, AT : 00000000 65950000, v0 : 00000000 65A902D0, v1 : 00000000 00000000
a0 : 00000000 00000001, a1 : 00000000 652F0000, a2 : 00000000 00000000, a3 : 00000000 00000000
t0 : 00000000 0000FF00, t1 : 00000000 3401FF01, t2 : 00000000 607C7C58, t3 : FFFFFFFF FFFF00FF
t4 : 00000000 607C7C58, t5 : 00000000 00000001, t6 : 00000000 652EB4C4, t7 : 00000000 652F0000
s0 : 00000000 00000000, s1 : 00000000 652F0000, s2 : 00000000 00000028, s3 : 00000000 60400834
s4 : 00000000 00000000, s5 : 00000000 00000000, s6 : 00000000 00000009, s7 : 00000000 00000028
t8 : 00000000 00008000, t9 : FFFFFFFF 80830000, k0 : 00000000 00000020, k1 : 00000000 00000000
gp : 00000000 65953500, sp : 00000000 66AEBCE8, s8 : 00000000 66360000, ra : 00000000 607C04D4
EPC : 607C1FCC, ErrorEPC : 9FC00500, SREG : 3401FF03
MDLO : 0001E848, MDHI : 00000000, BadVaddr : F57DEDAF
TEXT_START : 0x60015AB0
DATA_START : 0x63C861E0
Cause 00000024 (Code 0x9): Breakpoint exception
00:02:00 UTC Thu Jan 1 1970: Breakpoint exception, CPU signal 23, PC = 0x607C1FCC
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0x607BBDECz 0x607BA2F4z 0x62C964E0z 0x603FA65Cz 0x603EED14z 0x603EF10Cz 0x603EF1B0z 0x603F8F34z 0x60401E18z 0x617A5DBCz 0x617A6110z 0x6179FE84z 0x6179C4B4z 0x61198CC4z 0x61197420z 0x61197924z
$0 : 00000000 00000000, AT : 00000000 65950000, v0 : 00000000 65A902D0, v1 : 00000000 00000000
a0 : 00000000 00000001, a1 : 00000000 652F0000, a2 : 00000000 00000000, a3 : 00000000 00000000
t0 : 00000000 0000FF00, t1 : 00000000 3401FF01, t2 : 00000000 607C7C58, t3 : FFFFFFFF FFFF00FF
t4 : 00000000 607C7C58, t5 : 00000000 00000001, t6 : 00000000 652EB4C4, t7 : 00000000 652F0000
s0 : 00000000 00000000, s1 : 00000000 652F0000, s2 : 00000000 00000028, s3 : 00000000 60400834
s4 : 00000000 00000000, s5 : 00000000 00000000, s6 : 00000000 00000009, s7 : 00000000 00000028
t8 : 00000000 00008000, t9 : FFFFFFFF 80830000, k0 : 00000000 00000020, k1 : 00000000 00000000
gp : 00000000 65953500, sp : 00000000 66AEBCE8, s8 : 00000000 66360000, ra : 00000000 607C04D4
EPC : 607C1FCC, ErrorEPC : 9FC00500, SREG : 3401FF03
MDLO : 0001E848, MDHI : 00000000, BadVaddr : F57DEDAF
TEXT_START : 0x60015AB0
DATA_START : 0x63C861E0
Cause 00000024 (Code 0x9): Breakpoint exception
Nested write_crashinfo call (2 times)
00:02:00 UTC Thu Jan 1 1970: Breakpoint exception, CPU signal 23, PC = 0x607C1FCC
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0x607BBDECz 0x607BA2F4z 0x62C964E0z 0x603FA65Cz 0x603EED14z 0x603EF10Cz 0x603EF1B0z 0x603F8F34z 0x60401E18z 0x617A5DBCz 0x617A6110z 0x6179FE84z 0x6179C4B4z 0x61198CC4z 0x61197420z 0x61197924z
$0 : 00000000 00000000, AT : 00000000 65950000, v0 : 00000000 65A902D0, v1 : 00000000 00000000
a0 : 00000000 00000001, a1 : 00000000 652F0000, a2 : 00000000 00000000, a3 : 00000000 00000000
t0 : 00000000 0000FF00, t1 : 00000000 3401FF01, t2 : 00000000 607C7C58, t3 : FFFFFFFF FFFF00FF
t4 : 00000000 607C7C58, t5 : 00000000 00000001, t6 : 00000000 652EB4C4, t7 : 00000000 652F0000
s0 : 00000000 00000000, s1 : 00000000 652F0000, s2 : 00000000 00000028, s3 : 00000000 60400834
s4 : 00000000 00000000, s5 : 00000000 00000000, s6 : 00000000 00000009, s7 : 00000000 00000028
t8 : 00000000 00008000, t9 : FFFFFFFF 80830000, k0 : 00000000 00000020, k1 : 00000000 00000000
gp : 00000000 65953500, sp : 00000000 66AEBCE8, s8 : 00000000 66360000, ra : 00000000 607C04D4
EPC : 607C1FCC, ErrorEPC : 9FC00500, SREG : 3401FF03
MDLO : 0001E848, MDHI : 00000000, BadVaddr : F57DEDAF
TEXT_START : 0x60015AB0
DATA_START : 0x63C861E0
Cause 00000024 (Code 0x9): Breakpoint exception
-Traceback= 0x607BBDECz 0x607BA2F4z 0x62C964E0z 0x603FA65Cz 0x603EED14z 0x603EF10Cz 0x603EF1B0z 0x603F8F34z 0x60401E18z 0x617A5DBCz 0x617A6110z 0x6179FE84z 0x6179C4B4z 0x61198CC4z 0x61197420z 0x61197924z
Writing crashinfo to flash:crashinfo_19700101-000200-UTC
No warm reboot Storage mpsc_chr10 24030a30: 0x8080000
*** System received a System Error ***
signal= 0x16, code= 0x0, context= 0x65cd1814
PC = 0x607d56a4, Cause = 0x2020, Status Reg = 0x3401c102
System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2004 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127
c1841 processor with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabledC
