12-01-2010 06:01 AM - edited 03-06-2019 02:18 PM
Hi ,
i have a 4507R-E (Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-IPBASEK9-M), Vers
ion 12.2(53)SG2, RELEASE SOFTWARE (fc1))
with the following modules installed
sh module
Chassis Type : WS-C4507R-E
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
2 18 10GE (X2), 1000BaseX (SFP) WS-X4606-X2-E JAE144006QK
3 6 Sup 6L-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6L-E JAE14390RS5
7 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E JAE14390ELL
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
2 1cdf.0f7e.22e7 to 1cdf.0f7e.22f8 1.2 Ok
3 1cdf.0f51.e7c0 to 1cdf.0f51.e7c5 2.0 12.2(44r)SG5 12.2(53)SG2 Ok
7 1cdf.0f7d.eb2c to 1cdf.0f7d.eb5b 1.0 Ok
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active
On the SUP6L's both X2 ports i have installed the twin gig convertor module and inserted GLC-T on all 4 ports
DC_Core#sh int status module 3
Port Name Status Vlan Duplex Speed Type
Te3/1 inactive 1 full 10G No X2
Te3/2 inactive 1 full 10G No X2
Gi3/3 notconnect 200 full 1000 1000BaseT
Gi3/4 notconnect 200 full 1000 1000BaseT
Gi3/5 notconnect 1 full 1000 1000BaseT
Gi3/6 notconnect 1 full 1000 1000BaseT
All 4 Gig ports are shown as active while the 2 Tengig ports are inactive
DC_Core#sh hw-module module 3 port-group
Module Port-group Active Inactive
-------------------------------------------------------------
3 1 Gi3/3-4 Te3/1
3 2 Gi3/5-6 Te3/2
I am still unable to use these GLC-T modules to connect my router 2911's Gi0/0 port i have even tried connecting it to a laptop but no luck
Port settings are as below (VLAN 200 is already added in the database)
interface GigabitEthernet3/3
switchport access vlan 200
switchport mode access
!
interface GigabitEthernet3/4
switchport access vlan 200
switchport mode access
i have already applied the hw-module module 3 port group 1 (&2) select gigabitethernet (which worked while i was setting up the WS-4606-X2-E line card) and the hw-module uplink command is not available..
STUCK BADLY ! can anyone help.
Regards
Zaid
12-01-2010 09:22 PM
basically i just want to connect a router's gi0/0 to the SUP6L 's gi3/3. but the LEDs just vont come up.
any help would be appreciated.
regards
zaid
12-02-2010 02:33 PM
Straight-through cable?
Speed negotiated by the router is 1Gb?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide