I have a cisco C2950 and I've just did a firmware upgrade. I have downloaded the
c2950-i6q4l2-tar.121-22.EA14.tar and I've installed the firmware accordingly. Everything went well, the Switch is booting with new version etc..etc..
The problem I have is that when I try to access from the web, I can't see anything. The command for the http is enabled as well.
As per hereunder is the show version of the C2950
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA14, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by cisco Systems, Inc.
Compiled Tue 26-Oct-10 10:35 by nburra
Image text-base: 0x80010000, data-base: 0x80570000
ROM: Bootstrap program is C2950 boot loader
Switch uptime is 8 minutes
System returned to ROM by power-on
System image file is "flash:c2950-i6q4l2-mz.121-22.EA14.bin"
cisco WS-C2950-24 (RC32300) processor (revision Q0) with 20956K bytes of memory.
Processor board ID FOC0844Y05B
Last reset from system-reset
Running Standard Image
24 FastEthernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:12:7F:46:DB:80
Motherboard assembly number: 73-5781-13
Power supply part number: 34-0965-01
Motherboard serial number: FOC08440CJA
Power supply serial number: DAB0843JSQP
Model revision number: Q0
Motherboard revision number: A0
Model number: WS-C2950-24
System serial number: FOC0844Y05B
Configuration register is 0xF
Flash Directory As per herunder
Directory of flash:/
2 -rwx 110 Mar 01 1993 00:15:09 +00:00 info
3 -rwx 314 Mar 01 1993 00:21:02 +00:00 env_vars
4 -rwx 616 Mar 01 1993 00:24:32 +00:00 vlan.dat.renamed
6 -rwx 3132319 Mar 01 1993 00:17:11 +00:00 c2950-i6q4l2-mz.121-22.EA14.bin
8 drwx 4480 Mar 01 1993 00:17:54 +00:00 html
90 -rwx 110 Mar 01 1993 00:18:54 +00:00 info.ver
91 -rwx 1131 Mar 01 1993 00:02:16 +00:00 config.text.renamed
93 -rwx 5 Mar 01 1993 00:02:16 +00:00 private-config.text.renamed
Top upgrade the Firmware I 've used this link which was very pretty straight forward.
Will you please make sure you have the enable password configured as this is the default method of HTTP server user authentication. Should you decide you can configure other HTTP server interface authentication method via the "ip http authentication" command.
Thanks foir your reply,
I've already did that, I've manage to solve that by upgrading another firmware E10A crypto and without any setting whatsover I've managed to have web access. If I'm not mistaken the http access is on by default. So I dont know why with E14 firmware didn't work. The funny side is that while I was working with web base on version E10A, from the web I've decided to upgrade once again to E14 and it works.Now I'm using the latest firmware version and the latest Cisco SDM.
Kindly let this discussion open so people can solve their issue that I had.