cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Cisco Community Designated VIP Class of 2020

2345
Views
0
Helpful
2
Replies
Highlighted
Beginner

WS-C4507R - IOS Upgrade - Urgent

Guys

My upgrade is not going as smooth as I would like.  Blow is what I did and the errors/messages. Any idea how to recover the standby supervisor?

copy tftp://image.bin bootflash:image.bin

copy bootflash:image.bin slaveboot:image.bin

Switch# config terminal

Switch(config)# config-register 0x2

Switch(config)# boot system flash slot0: cat4000-is-mz.121-11b.EW

Switch# copy running-config start-config

Switch# redundancy reload peer

After the peer reloaded this is what I'm having

25w5d: %C4K_REDUNDANCY-6-MODE: ACTIVE supervisor initializing for rpr mode

25w5d: %C4K_REDUNDANCY-2-IOS_VERSION_CHECK_FAIL: IOS version mismatch. Active supervisor version is 12.1(19)EW1,. Standby supervisor version is 12.2(54)SG1,. Redundancy feature may not work as expected.

25w5d: %C4K_REDUNDANCY-5-CONFIGSYNC: The bootvar has been successfully synchronized to the standby supervisor

25w5d: %C4K_REDUNDANCY-5-CONFIGSYNC: The config-reg has been successfully synchronized to the standby supervisor

25w5d: %C4K_REDUNDANCY-5-CONFIGSYNC: The calendar has been successfully synchronized to the standby supervisor

25w5d: %C4K_REDUNDANCY-5-CONFIGSYNC: The startup-config has been successfully synchronized to the standby supervisor

25w5d: %C4K_REDUNDANCY-5-CONFIGSYNC: The private-config has been successfully synchronized to the standby supervisor

25w5d: %C4K_REDUNDANCY-5-CONFIGSYNC_RATELIMIT: The vlan database has been successfully synchronized to the standby supervisor

Show redundancy states

       my state = 13 -ACTIVE

     peer state = 1  -DISABLED

           Mode = Simplex

           Unit = Primary

        Unit ID = 1

Redundancy Mode (Operational) = RPR

Redundancy Mode (Configured)  = RPR

     Split Mode = Disabled

   Manual Swact = Disabled  Reason: Simplex mode

Communications = Down      Reason: Simplex mode

   client count = 4

client_notification_TMR = 60000 milliseconds

          keep_alive TMR = 9000 milliseconds

        keep_alive count = 0

    keep_alive threshold = 18

           RF debug mask = 0x0

SHow module

Chassis Type : WS-C4507R

Power consumed by backplane : 40 Watts

Mod Ports Card Type                              Model              Serial No.

---+-----+--------------------------------------+------------------+-----------

1     2  1000BaseX (GBIC) Supervisor(active)    WS-X4515           JAE080200S5

2        Standby Supervisor

3    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE07510SEC

4    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE0751010W

5    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE0752019F

6    48  10/100BaseTX (RJ45)                    WS-X4148-RJ        JAE07510S4V

7    18  1000BaseX (GBIC)                       WS-X4418-GB        JAE0746099M

M MAC addresses                    Hw  Fw           Sw               Status

--+--------------------------------+---+------------+----------------+---------

1 000e.d798.1880 to 000e.d798.1881 3.1 12.1(20r)EW  12.1(19)EW1, EAR Ok

2 Unknown                              Unknown      Unknown          Other

3 000e.8359.95c0 to 000e.8359.95ef 3.1                               Ok

4 000e.8359.2a80 to 000e.8359.2aaf 3.1                               Ok

5 000e.8366.7360 to 000e.8366.738f 3.1                               Ok

6 000e.831d.1220 to 000e.831d.124f 3.1                               Ok

7 000d.bcf6.547e to 000d.bcf6.548f 1.4                               Ok

Thanks Guys

Everyone's tags (4)
2 REPLIES 2
VIP Expert

WS-C4507R - IOS Upgrade - Urgent

You have IOS mismatch.  You need to load the same exact IOS in both sups and then reboot the switch. You also need to configure the primary sup with this command. 

redun mode sso

HTH

Reza

Beginner

WS-C4507R - IOS Upgrade - Urgent

Hi Reza,

Thanks for your quick response.

I've already copied the same image to the bootflash: and the slaveboot:

I was hoping to avoid reloading the switch and take advantage of it's redundant capabilities.

Is there anyother work around other than restarting?

CreatePlease to create content
Content for Community-Ad