We have a WS-C4948-10GE that we are looking to load 15.0 code on. The version that I've loaded on the device is cat4500-entservicesk9-mz.150-2.SG10.bin
After setting the 4948 to boot using that file, the switch hangs after displaying the following output:
**********************************************************
* *
* Welcome to Rom Monitor for WS-C4948-10GE System. *
* Copyright (c) 2003-2009, by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.2(31r)SGA4
Supervisor: WS-C4948-10GE Chassis: WS-C4948
Hardware Revisions - Board: 8.5 CPLD Gill: 19
MAC Address : 00-27-0d-b3-b1-7f
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
. . . . .
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Current BOOT file is --- bootflash:cat4500-entservicesk9-mz.150-2.SG10.bin
Rommon reg: 0x00004180
############
Decompression done, relocating ...
k2diags version 5.7
prod: WS-C4948-10GE part: 73-9344-12 serial: FOX1333GVT8
Power-on-self-test for Module 1: WS-C4948-10GE
Port/Test Status: (. = Pass, F = Fail, U = Untested)
Cpu Subsystem Tests ...
seeprom: . temperature_sensor: .
Port Traffic: L2 Serdes Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: .
36: . 37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: .
62: . 63: .
Port Traffic: L2 Asic Loopback ...
0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .
12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .
24: . 25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: .
36: . 37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: .
62: . 63: .
Switch Subsystem Memory ...
1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: . 12: .
13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: .
25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: . 36: .
37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: .
49: . 50: . 51: .
Module 1 Passed
Exiting to ios...
Rommon reg: 0x00000180
#######################################################
Decompression done, relocating ...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 15.0(2)SG10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 07-Apr-15 09:46 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x123AE824
I get no further response from the console after the last line.
We've tried two different 15.0 code revisions with the same behavior. Would greatly appreciate any ideas.
