Tag: "port_issues" in "Technology and Support"

Buy or Renew

Latest Tagged

Unable to connect Catalyst switch to the Ether Switch Module on a router that uses the straight thro... - ( ‎06-22-2009 03:42 PM )

by on

0 Replies 564 Views

0 Replies

564 Views

Port status is errdisable due to EtherChannel misconfiguration - ( ‎06-22-2009 05:10 PM )

by on

0 Replies 20502 Views

0 Replies

20502 Views

Packet loss occurs when the block unicast feature is enabled in Catalyst 6500 series switches that r... - ( ‎06-22-2009 04:40 PM )

by on

0 Replies 2080 Views

0 Replies

2080 Views

The "%C4K_HWPORTMAN-4-BLOCKEDTXQUEUE" error message on Cisco Catalyst 4500 series switches connected... - ( ‎06-22-2009 05:34 PM )

by on Latest post on by

2 Replies 21653 Views

2 Replies

21653 Views

The Catalyst 4500 series switch that runs Cisco IOS software reboots with the "%% Low on memory; try... - ( ‎06-22-2009 05:04 PM )

by on

0 Replies 2500 Views

0 Replies

2500 Views

Port status is errdisable due to BPDU guard - ( ‎06-22-2009 04:02 PM )

by on

0 Replies 171754 Views

0 Replies

171754 Views

The "PAGP-5 or%ETHC-5" error messages or link flaps on a port and EtherChannel are possibly not conf... - ( ‎06-22-2009 05:10 PM )

by on

0 Replies 4249 Views

0 Replies

4249 Views

The %SYS-4-P2_WARN: 1/Blocked queue (tx) on port error message is displayed on a Cisco Catalyst 4000... - ( ‎06-17-2009 10:14 PM )

by on

0 Replies 634 Views

0 Replies

634 Views

A SPAN destination port is shown as "not connected" and does not communicate with the rest of the ne... - ( ‎06-22-2009 05:35 PM )

by on

0 Replies 6737 Views

0 Replies

6737 Views

Ports 1/2 and 2/2 are inactive with dual supervisor engines in Cisco Catalyst 4507R switches - ( ‎06-22-2009 05:04 PM )

by on Latest post on by

1 Replies 1383 Views

1 Replies

1383 Views

Top Tagged

When port security is enabled, MAC addresses are detected but after a short while the port is shut d... - ( ‎06-22-2009 06:12 PM )

by on

0 Replies 1165 Views

0 Replies

1165 Views

The "%DOT1X_SWITCH-5-ERR_ADDING_ADDRESS:" error message appears in Cisco Catalyst 3550 or 3750 serie... - ( ‎06-22-2009 06:07 PM )

by on Latest post on by

2 Replies 7016 Views

2 Replies

7016 Views

How to run GOLD diagnostic tests on Catalyst 6500/6000 series switches to troubleshoot hardware issu... - ( ‎06-22-2009 05:38 PM )

by on

0 Replies 17407 Views

0 Replies

17407 Views

How to configure the errdisable flap-setting values in Cisco Catalyst switches running Cisco IOS sys... - ( ‎06-22-2009 05:37 PM )

by on Latest post on by

2 Replies 12440 Views

2 Replies

12440 Views

User cannot get a Gigabit Ethernet link up between a Cisco switch and a non-Cisco device due to auto... - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 1184 Views

0 Replies

1184 Views

The %RTD-1-LINK_FLAP [chars] link down/up [dec] times per min error message appears on a port - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 3721 Views

0 Replies

3721 Views

Runts and CRC errors increment in the show interface command output on a Cisco IOS-based switch, or ... - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 69341 Views

0 Replies

69341 Views

A SPAN destination port is shown as "not connected" and does not communicate with the rest of the ne... - ( ‎06-22-2009 05:35 PM )

by on

0 Replies 6737 Views

0 Replies

6737 Views

The "%C4K_HWPORTMAN-4-BLOCKEDTXQUEUE" error message on Cisco Catalyst 4500 series switches connected... - ( ‎06-22-2009 05:34 PM )

by on Latest post on by

2 Replies 21653 Views

2 Replies

21653 Views

When redundancy is run, unable to use all eight ports on both of the Supervisor 5 engines in a Catal... - ( ‎06-22-2009 05:33 PM )

by on

0 Replies 1046 Views

0 Replies

1046 Views

Top Taggers

User

Count