Tag: "port_issues" in "Networking"

Buy or Renew

Latest Tagged

The user is unable to assign an IP address to a Layer 3 (L3) sub-interface on a Catalyst 3750 or 355... - ( ‎06-22-2009 04:06 PM )

by on

0 Replies 3436 Views

0 Replies

3436 Views

Unable to connect Catalyst switch to the Ether Switch Module on a router that uses the straight thro... - ( ‎06-22-2009 03:42 PM )

by on

0 Replies 754 Views

0 Replies

754 Views

Recovering from ErrDisabled port due to misconfiguration - ( ‎06-22-2009 04:39 PM )

by on Latest post on by

2 Replies 243938 Views

2 Replies

243938 Views

How to configure the Gigabit Ethernet fiber-optic interface to support duplex speed in Cisco Catalys... - ( ‎06-22-2009 04:11 PM )

by on

0 Replies 10370 Views

0 Replies

10370 Views

The %SYS-4-SYS_LCPERR4:Module [dec]: LTL Parity error detected on Coil #[dec] error message appears... - ( ‎06-22-2009 04:06 PM )

by on

0 Replies 3491 Views

0 Replies

3491 Views

When port security is enabled, MAC addresses are detected but after a short while the port is shut d... - ( ‎06-22-2009 06:12 PM )

by on

0 Replies 1308 Views

0 Replies

1308 Views

The %PM_SCP-SP-3-LCP_FW_ABLC: Late collision message from module error message appears in Catalyst ... - ( ‎06-22-2009 04:38 PM )

by on Latest post on by

1 Replies 10923 Views

1 Replies

10923 Views

How to prevent the input queue drops and output queue drops in Catalyst switches running Cisco IOS s... - ( ‎06-22-2009 04:05 PM )

by on

0 Replies 5860 Views

0 Replies

5860 Views

A VLAN might disappear due to a duplex mismatch, which causes connectivity issues - ( ‎06-22-2009 04:12 PM )

by on

0 Replies 696 Views

0 Replies

696 Views

Input errors on the Layer-3 interface of Catalyst 6500 switch running Cisco IOS when connected to th... - ( ‎07-01-2009 04:57 AM )

by on

0 Replies 2812 Views

0 Replies

2812 Views

Top Tagged

When port security is enabled, MAC addresses are detected but after a short while the port is shut d... - ( ‎06-22-2009 06:12 PM )

by on

0 Replies 1308 Views

0 Replies

1308 Views

The "%DOT1X_SWITCH-5-ERR_ADDING_ADDRESS:" error message appears in Cisco Catalyst 3550 or 3750 serie... - ( ‎06-22-2009 06:07 PM )

by on Latest post on by

2 Replies 8284 Views

2 Replies

8284 Views

How to run GOLD diagnostic tests on Catalyst 6500/6000 series switches to troubleshoot hardware issu... - ( ‎06-22-2009 05:38 PM )

by on

0 Replies 18411 Views

0 Replies

18411 Views

How to configure the errdisable flap-setting values in Cisco Catalyst switches running Cisco IOS sys... - ( ‎06-22-2009 05:37 PM )

by on Latest post on by

2 Replies 14385 Views

2 Replies

14385 Views

User cannot get a Gigabit Ethernet link up between a Cisco switch and a non-Cisco device due to auto... - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 1388 Views

0 Replies

1388 Views

The %RTD-1-LINK_FLAP [chars] link down/up [dec] times per min error message appears on a port - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 3932 Views

0 Replies

3932 Views

Runts and CRC errors increment in the show interface command output on a Cisco IOS-based switch, or ... - ( ‎06-22-2009 03:40 PM )

by on

0 Replies 77856 Views

0 Replies

77856 Views

A SPAN destination port is shown as "not connected" and does not communicate with the rest of the ne... - ( ‎06-22-2009 05:35 PM )

by on

0 Replies 8251 Views

0 Replies

8251 Views

The "%C4K_HWPORTMAN-4-BLOCKEDTXQUEUE" error message on Cisco Catalyst 4500 series switches connected... - ( ‎06-22-2009 05:34 PM )

by on Latest post on by

2 Replies 22437 Views

2 Replies

22437 Views

When redundancy is run, unable to use all eight ports on both of the Supervisor 5 engines in a Catal... - ( ‎06-22-2009 05:33 PM )

by on

0 Replies 1183 Views

0 Replies

1183 Views

Top Taggers

User

Count