Hi all,I want to ask you experts some suggestion on how really work mechanism between Cisco switches and radius server when using dynamic vlan assignement and the radius suddenly will be unavailable.With server dead command under port configuration i...
Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question: Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...
OK, so I've got a set of ASA's and we are migrating them to Firepowers, and all seems ok. In the past we have noticed that for some reason on the ASA's, no matter what you specify as the parameters for phase 1, the rekey timer always connects at 3600...
Hello we have a local 9120axi AP with a 9800LC WLC that seems to be losing connection. The AP is in flex connect, all config looks fine: AdvancedCountry CodeUS Multiple CountriesUSStatistics Timer180CAPWAP MTU1485AP Link LatencyEnabledAP PMK Propaga...
Good day to everyone.I have two Cisco ASA running on FPR2130 assembled into a balancing group, for example:vpn-gw1.example.comvpn-gw2.example.comgeneral address vpn.example.com.Firmware version 9.18.3.56Anyconnect 4.10.07062At the moment, all our emp...
We are a healthcare facility. For past several months we have had several complaints from users that calls are often full of static. We are running CUCM 12.5(1)SU8 and the phones are primarily 8811 running current firmware. We have replaced phon...
Hello Everyone, I am contacting you all because i don't seem to find the needed information to resolve my issues, even though there are many similar topic as mine with the same error.We have an infrastructure using FTD ASA5506 with switch CISCO WS-C2...
Hi All,I have a couple of C9300 L3 switches that are connecting to an ASA firewall. The NTP and the syslog server for the switches are located behind a firewall.When one of the switches request/send packets the gateway IP is the source address on the...
Fixing cast iron without welding can be effectively accomplished through the use of a metal epoxy. This method involves cleaning the broken pieces thoroughly to remove any dirt, grease or rust. Once clean, apply a high-quality metal epoxy over the br...
After searching through other posts, my config seems OK but still strange behaviourasa 9.20 running on FPWR chasisI cannot get in enabled mode when connecting to ASA via console.It used to work but stopped after I played (disable and restore) with aa...
Hi,I am trying to set up an SSH connection to my switch, but right now there is some lower level problem. I have set up my FastEthernet0 interface to ip address dhcp and the command show interfaces FastEthernet0 shows the correct address. Even if I t...
hi i am trying to cable up trhe ucs 6454. I got 2 40G mopdules on port 53 and 54 on each fabric. I got 2 core switches to connect therm to FABRIC 1port 53 ----> port 1 on Core switch APort 54 -----> port 1 on Core Switch BFABRIC 2port 53 ------> port...
I am user with customer administrator role but still unable to get access to EOX API . When in try API request I get eh below 403 Forbidden error. Do let me know if any other details is needed.
Hello,I have a C1300, I use it as my IPv4 and IPv6 gateway for internal routing. It has a default gateway to another router for internet access. If I perform an IPv6 speedtest with the c1300 as my gateway for IPv6 then I get around 1Mb, this is stran...
Deployed a 3100 in chassis mode to the FMC a few days ago. All went to plan.Determined we needed to change the IP so decided just to delete the device from FMC and re-provision it.On the FTD via local-mgmt did a erase configuration. The device wiped ...